Yamaha YAS-70 owner manual Attaching the center system to a wall

Page 12

Placing this system

Attaching the center system to a wall

You can attach the center system to a wall using commercially available screws (#8, Diameter: 7.5 mm or more (9/32” or more)).

When installing the center system on a wall, all installation work must be performed by a qualified contractor or dealer personnel. The customer must never attempt to perform this installation work. Improper or inadequate installation could cause the center system to fall, resulting in personal injury.

1 Attach the supplied mounting template on a wall and then mark the holes of the mounting template.

Tapes or thumbtacks

Mark

2 Remove the mounting template and then install the commercially available screws at the marks.

Diameter:

7.5 mm or more (#8, 9/32” or more)

4 to 6 mm (3/16” to 1/4”)

Installing the cables above the center system

To pass the cables upward, you need to attach the spacers to make room on the back of the center system.

In step 2 of the left column;

2-a: Attach the supplied spacers to the rear panel of the center system using the supplied double-sided tapes. You can choose either the side A or the side B.

For narrow space

For wide space

Large double-

Small double-

sided tape

sided tape

Attach

Attach

y

To install the cables above the center system, refer to the right column.

3 Hang the center system on the screws using the holes on the back of the center system.

2-b: Remove the mounting template and then install the commercially available screws at the marks.

22 to 24 mm

34 to 36 mm

(7/7” to 15/16”)

(5/16” to 7/16”)

Notes

The center system weighs about 4.5 kg (9 lbs. 15 oz.). To attach the center system to a wall using screws, the wall must be firm. Do not attach the center system to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the center system to fall.

Use commercially available screws that can endure weight enough.

Make sure you use specified screws to attach the center system to a wall. Using clamps other than specified screws, such as short screws, nails, or two-sided tape, may cause the center system to fall.

When connecting the center system, fix the speaker cables in place so that cables do not loosen. If your foot or hand accidentally gets caught on a loose speaker cable, the center system may fall.

After attaching the center system, check that the center system is fixed securely. Yamaha will bear no responsibility for any accidents caused by improper installations.

8 En

Image 12
Contents YAS-70 Important Safety Instructions FCC Information for US customers Iii En Contents Accessories Getting startedSupplied parts UnitsVolume + Controls and functionsFront panel of the center system Input STANDBY/ONVolume Front panel display of the center systemRemote control Infrared signalSound field program buttons Input buttonsUsing the remote control Installing the batteriesPlacing this system Placing the center systemPlacing the center system above/beneath a TV Center system YAS-70CUInstalling the cables above the center system Attaching the center system to a wallConnecting speaker cables Connecting system control cableConnection Connecting external components Digital connectionInput 1 Optical jack Input 2 Coaxial jackAnalog connection Input 3 Analog jacksExample1 TV Example 2 VCR or video cameraConnecting a Yamaha iPod universal dock Connecting the indoor FM antennaConnecting the power cable Press Volume +/- to adjust the volume level. y Basic playback operationPress one of the input buttons to select an input source Start playback on the selected external componentEnjoying various sound features Enjoying realistic sounds Sound field programPress one of the sound field program buttons Sound field program descriptionsListening at low volume Night listening mode Decoder mode descriptionsPress Night PL II MovieFM tuning Controls and functions for the FM tuningOverview Basic tuning operation Press AUTO/MAN’L so that the Auto indicatorManual tuning Pressmode.FM to select this system to the FM tunerUsing station preset feature Automatic station presetRecalling the preset stations Manual station preset Press Memory to confirm the presetPress Memory Using iPod Controls and functions for iPodDock Playback control buttonsUseful operation Changing the brightness of the front panel displayTurning off the front panel display Press Dimmer repeatedlyAdjusting the virtual speaker settings Adjusting the characteristics of the tonal quality PAdjusting the volume balance during playback P Sound image of this systemUsing the speaker test mode Adjusting the volume balance of each channelAdjusting the position of the virtual surround speakers Pressmode.TEST again to exit from the speaker testAdjusting the characteristics of the tonal quality Room EQ Adjusting the speaker balance during playbackSW + Center +Troubleshooting Additional informationTuner IPodGlossary Cinema DSPDTS Specifications YAS-70CUYAS-70SPX WM26020