Konica Minolta F-2900 instruction manual Connecting the Scsi Cable, Connecting the Hardware

Page 11

CONNECTING THE HARDWARE

Connecting the SCSI Cable

This scanner has been packaged with the SCSI cable SC-11 (DB25-to-SCSI-1). See your dealer if you require a different SCSI cable.

• To meet FCC regulations, the SCSI cables used with this scanner must be equipped with ferrite cores.

BEFORE YOU BEGIN…

TURN THE COMPUTER AND ALL CONNECTED

DEVICES OFF.

1. Place the scanner on a level surface.

2. Connect one end of the SCSI cable to either SCSI port on the back of the scanner

• Either SCSI port can be used for other configurations, there is no dedicated in or out port.

3.Connect the other end of the SCSI cable to the SCSI port on the computer or the last device in the SCSI chain.

Continued on the following page.

9

Image 11

Contents 9224-2885-11 H-A909 Page To avoid fire or electric shock For Proper and Safe USEMonitor Other System Requirements PC ATSystem Requirements Macintosh Software Registration Following contents should be included in this packageTable of Contents Scanner Names of Parts Scanner Setup Setting the Scsi ID Setting the Scsi IDScsi ID Dip Switch Settings Connecting the Hardware Connecting the Scsi CableIf there are other devices in your Scsi chain… Turn the terminator power switch switch 4 to on Windows Installing the Software PC/ATClick on Cancel Windows Windows 95 Release 2 OSR2Then click on Next Setup will begin Double-click on Driver folder Installing the Software MacintoshDouble-click on You can also click on to select an install drive A N D a R D O P E R a T I O N Launching the Software Launching the Twain Driver WindowsDouble click on Launching the Plug-in MacintoshLaunching the Utility Software Windows MacintoshMain WINDOW-NAME of Parts Command Window part Name of partsMain window Set the preferences as desired Setting the PreferencesClick on to accept the new preference settings Preference Dialog Box Name of partsLoading the Film Holder Loading the Negative HolderInsert slides into the slide holder emulsion side up Loading the Slide HolderInserting the Film Holder Into the Scanner Select 35mm from the film format Drop-down list Setting the Film TypePREVIEW-SETTING Film Type Preview window part Name of parts AUTO-EXPOSURE Lock Setting AE-LockCancelling AE-Lock While pressing down the Shift key, change the AE area AE Area LockClick on Press the Shift key Orienting the Image RotateClick on to flip the image left-to-right FlipClick on to flip the image top to bottom Cropping Auto CroppingMagnifying or Reducing the View RGB/CMY information ScrollAPS formats C, H and P APS only Displaying Frame number APS onlyImage correction window part Name of parts Image Correction Tone CURVES/HISTOGRAM Draw the desired curve by dragging Correcting the Tone CurvesChanging Tone Curves by Freehand Click the RGB Display button Correcting the HistogramDisplaying the Histogram of Each R, G, B color Click the desired highlight point of the image Setting the White or Black PointsSetting the White Point Double-click the White Point button Setting the Black Point Double-click the Black Point buttonClick the point to be changed to gray in the image Setting the Gray PointAuto setting Click the Gray Point buttonImage Correction BRIGHTNESS/CONTRAST/COLOR Balance Post-Correction LUT Pre-Correction Color Sample and Post-Correction Color Sample Image Correction HUE/SATURATION/LIGHTNESSReset Image Correction Variation Correction Selecting the Correction ItemCorrect the image by repeating the operation in step Color Balance CorrectionBrightness & Contrast Correction Click the colour balanceSaturation Correction Click on the thumbnail in the Snapshot Display Area Storing in the Snapshot Display Area temporarilyDisplaying the image stored temporarily as a preview image Image Correction SnapshotChecking the Correction Result While Lining Up Images Full-Screen ViewClick the Full-Screen View button Input the job name and click on the OK button Image Correction JOB SAVE/JOB LoadDelete the Image Correction Loading Image Correction JobRedo the Correction Navigation Dialog box Name of parts NavigationOperation item checkbox Navigation MenuClick the Navigation Start button Select the setting to be deleted and click the Delete button Saving, Selecting and Deleting a Navigation SettingFinal Scan Twain Driver Plug-in SoftwareUtility Software A N N I N G a P S F I L M Launch Software Specify Film Type Set the Preferences as desired in the APS settings part Preferences APS SettingsSlide the film-chamber release as shown Names of PartsLoading the APS Adapter APS Adapter OptionalInserting the APS Adapter Index Scan Index Window Names of PartsClick on to reverse the display order Select the desired frames, then click on , or Rotating the Index FramesClick on the corner tab and drag to reach the desired size Close the Preview window to return to the Index window Preview and Image CorrectionClick on to scan the selected images Selecting FramesScanning the Image Click on an image to select it for scanningClick on to rewind the film into the cassette Removing the APS AdapterPage P E N D I Color Matching Color Matching in the Preference Dialog Box Name of partsSelect the ICC profile according to the monitor being used When using Photoshop Ver.3.0.5 or VerExcept the Image Correction window in the Main window Scan Settings part in the Main Window Names of partsScan Settings Job names Enter the desired output size maximum 3 digits Creating / Deleting JOB Files Creating a JobDeleting a Job Photosensitive Scan Job Category Description CustomColor Laser PrinterCategory Job name Out Mag Unit Scan JOB File List 35MMCategory Job Name Out Mag Scan JOB File List APS Contrast GlossaryShadows Trouble Shooting SolutionPrescan Sec Scan 40 sec Index Scan Sec/frame Interface Specifications17.28 x 29.95mm 1920 x 3328 pixels User Technical Support Determining the version number of your driver software