Kodak 6B7198 manual Mm double

Page 39

Validating the Scanner

3.Use the table below only as a starting point for determining Scan Area values.

NOTE: Keep the Line Offset (y): at the default value of 0 and keep Pixel Summing at the default value of None.

IMPORTANT: The Pixel Offset must be greater than or equal to the first calibrated pixel and # Pixels must be less than or equal to the last calibrated pixel minus the first calibrated pixel.

	Cut-Gate Film	Magnification	# Pixels	Pixel Offset	# Lines	File Size
	Holders	Magnification	# Pixels	Pixel Offset	# Lines	(MB)
	Holders					(MB)


	35 mm double-	0.50	1033	2484	1460	4.3
	perforated
	perforated	1.03	2129	1936	3008	18.3
		1.03	2129	1936	3008	18.3

		2.00	4133	934	5840	69.1

	46 mm	0.50	1754	2123	2554	12.8

		0.60	2105	1948	3065	18.5

		1.58	5542	229	8071	128.0

	6 x 4.5 cm	0.50	2368	1816	1539	10.4
	vertical
	vertical	0.66	3126	1437	2031	18.2
		0.66	3126	1437	2031	18.2

		1.26	5967	17	3878	66.2

	6 x 4.5 cm	0.50	1539	2231	2368	10.4
	horizontal
	horizontal	0.66	2031	1985	3126	18.2
		0.66	2031	1985	3126	18.2

		1.26	3878	1061	5967	66.2

	6 x 6 cm	0.50	2368	1816	2250	15.2

		0.55	2605	1698	2475	18.5

		1.26	5967	17	5670	96.8

	6 x 7 cm	0.50	2368	1816	2775	18.8

		1.26	5967	17	6994	119.4

	6 x 9 cm	0.50	2368	1816	3325	22.5

		1.19	5636	182	7914	127.6

	Split 70 mm	0.50	2483	1759	1632	11.6

		0.63	3129	1436	2056	18.4

		1.20	5960	20	3917	66.8

	70 mm	0.50	2682	1659	3450	26.5

		1.09	5846	77	7522	125.8

	4 x 5 in.	0.50	3972	1014	5026	57.1

		0.74	5878	61	7439	125.1

	max mag	2.00	6000	0	7333	125.9

	min mag	0.50	2917	1542	3750	31.3

May 2002

3-7

Image 39

Contents Plus and Universal Film Scanners Kodak Professional HRPage Kodak Professional May Regulatory Information Electrical Hazard Symbol Hot Surface Symbol Fuse LabelWarranty Repair Coverage Warranty InformationMechanical Hazard Symbol Warranty PeriodLimitations Kodak Service AgreementsContents Contents About This Guide Using This GuideAbout This Guide Introduction and Overview Product DescriptionHow the Scanner Works Features and Benefits Action or Condition Need to Calibrate? Focus? Before You BeginEquipment Overview Front ViewRear View Recommended Configuration of the Host Computer Host Computer Hardware RequirementsRecommended Software Requirements Film Holders Provided with the Scanner Film SizesPreparing the Host Computer Connecting and Operating the ScannerConnecting the Scanner Changing the AC Input Voltage Setting and the Fuses Fuse arrow Fuse in holder Close the AC input module Attaching the Cables Placing the Empty Film Holder in the Film Holder Guide Starting Up the Scanner SystemPowering up the Scanner and the Host Computer Selecting the Negative or Positive Balancing Filter Setting the Magnification and Calibrating ScannerSetting the Scan Parameters Operating the ScannerRed handle is in NEG position Preparing a Carded Negative Placing a Negative or Mounted Slide in the Film HolderPreparing a Mounted Slide Preparing an Uncarded NegativePlacing the Film Holder in the Scanner Focusing Shutting Down the ScannerScanning a Single Frame Connecting and Operating the Scanner Validating the Scanner Starting the SAM Software Validating the Scanner Select a Chosen Magnification Click Do Magnification Setting the MagnificationCalibrating the Scanner Select Save image to file Making a Test ScanMm double Autofocusing Checking the Scan Scanning the ImageSet Depth to 16 Bits Set Byte Order to IBM PC Cleaning Procedures Cleaning the LensMaintaining the Equipment Replacement Procedures Cleaning the Light BarReplacing the Lamp Leads Replacing the Round Balance Filters Replacing the Square IR Filter Maintaining the Equipment Appendix a Using the Service and Assembly Module SAM Backing Up Scanner Files Installing the Service and Assembly Module SAM SoftwareUsing Operations May Performing the Functions on the Mag/Focus Tab Setting the MagnificationPerforming an Autofocus Setting Image Processing Parameters Calibrating the Scanner Using the Capture TabScanning the Image Data Setting the Scan AreaUsing the Miscellaneous Tab Backing Up and Restoring Files Using the Service and Assembly Module SAM Accessories Appendix B Ordering Accessories and SuppliesSupplies Available AccessoriesSite Specifications Appendix C Scanner SpecificationsScanner Specifications Appendix D Using the Long Roll Accessory Downloading the Software and Firmware from Installing the Software for the Long Roll AccessoryUpgrading the Scanner’s Firmware Using the Long Roll Accessory Overview of Parts Installing or Removing the Long Roll AccessoryPreparing the Scanner for the Long Roll Accessory Mounting screws Connector Guide pins Attaching the Long Roll Accessory to the Scanner Alignment block Dowel pin Long Roll Accessory Rear mounting Latching and Unlatching the Gate Actuator Latching the Gate ActuatorUnlatching the Gate Actuator 120/220 Installing the Aperture PlateTo avoid dropping the screws inside the scanner Removing the Long Roll Accessory from the ScannerPunch Sensors Setting the Punch Reader Height for the Current Film SizeAdjusting the Core Locator Height on the Spindle Loading and Threading Film Threading the Film Setting the Punch Reader Height Click Load Film 120/220 Installing the Adjustment ToolVisually Checking the Punch Reader Height Adjusting the Punch Reader Height Preparing and Loading the Film Appendix D-1 Calibrating the Sensor OffsetsSetting the Lens Magnification Set the Line Offset y to Set Pixel Summing to None Type -1 in the First Punch Number field Locating the First Punched FrameUsing the Long Roll Accessory Checking the Alignment and Adjusting the Sensor Offsets Set Position Button Increments to 0.05 inches Using the Long Roll Accessory Recording the Highest Numbers on the LEDs Appendix D-2 Determining and Setting the Trigger PointsDetermining the Right Trigger Point Determining the Left Trigger PointSetting the Trigger Points at the Scanner Appendix D-3 Maintenance Cleaning the Punch Readers Cleaning the Rollers On the Film Controls window, click Stop Resetting the Sensors to the Factory Values Appendix D-4 Initial Setup of SensorsProgramming the Left Sensor Programming the Sensors for the Long Roll AccessoryProgramming the Right Sensor Appendix D-5 Table of Scan Area Values Punching Appendix D-6 Film Splicing and Editing GuidelinesNumerics IndexIndex Index Index