3. INSTALLATION
Notes:
•The attached screws and anchors are used to install the camera to a solid surface. (e.g. concrete) If installing to loose or thin material surfaces , use the appropriate anchors (not included) with the screws.
•Install the camera tightly.
(1)Attach the Alignment Sticker to the surface.
(2)Drill three pilot holes (Ø0.28inch×1.57inches(D)(Ø7mm×40mm(D))) through the three circles on the sticker.
(3)Hammer the supplied plastic anchors into the holes.
(4)Drill a hole (Ø0.63inch(Ø15mm) in the center of the sticker, and lead the video and power cables in this hole.
(5)Align the three holes of the Mounting Bracket with the three plastic anchors; insert the supplied screws with camera to corresponding holes.
(3)Turn the camera to the desired position, rotate the Clamp Ring clockwise to secure the camera.
(4)To adjust zoom and focus, loosen two controller screws, and move them to the desired position.
(5)Tighten zoom and focus controller screws. To secure these screws tightly, be sure to tighten them using a screwdriver.
(6)To secure the camera tightly, be sure to tighten the two Locking Screws using a screwdriver.
Note:
•Adjust the shade position after replacing original screw by hexagonal screw of accessories.
•Be sure to securely tighten the Clamp Ring.
3-3 Adjusting the BLC and AGC
AGC and BLC selecting switches are
4. NOTES ON USE AND INSTALLATION |
• Do not aim the camera at the sun |
Never aim the camera at the sun even with the camera power off. |
• Do not shoot intense light |
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe |
may appear on the screen. However, this is not a malfunction. |
• Treat the camera with care |
Do not drop the camera or subject it to intense vibration. |
• Never touch internal parts |
Do not touch the internal parts of the camera other than the parts specified. |
• Do not submerge in water |
Install the camera where the camera can be used indoors or outdoors according |
to IP66 code. If the camera was dropped in the water, turn off the power and |
contact your dealer. |
• Keep the camera installation away from video noise |
If cables are wired near electric lighting wires or a TV set, noise may appear in |
images. In this event relocate cables or reinstall equipment. |
• Check the ambient temperature and humidity |
Avoid using the camera where the temperature is hotter or colder than the |
1.Replace original screw by hexagonal screw of accessories, and temporarily fix it.
2.Adjust the shade to the best position.
3.Secure this screw by using a wrench (not included).
Alignment Sticker
Anchor
Clamp Ring
Screw
Locking Screw
(1)Backlight Compensation (BLC)
The exposure is automatically adjusted so that the best picture is obtained at a monitor zone of about 50% in the horizontal and about 50% in the vertical directions. The factory setting is "ON".
(2)Auto Gain Control (AGC)
Camera maximum gain can be selected High (30dB) or Low (24dB). The factory setting is "High". If the image is noisy in
3-4 Day / Night Function
specified operating range. Doing so could affect the internal parts or cause the |
image quality to deteriorate. Special care is required to use the camera at high |
temperature and humidity. |
• Should you notice any trouble |
If any trouble occurs while you are using the camera, turn off the power and |
contact your dealer. If you continue to use the camera when there is something |
wrong with it, the trouble may get worse and an unpredictable problem may occur. |
5. IN CASE OF PROBLEMS |
(1)The camera direction can be adjusted horizontally (pan: max. 360 deg.)
and vertically (tilt: max. 90 deg.).
(2)To adjust pan and tilt rotate the Clamp Ring counterclockwise, and loosen the two Locking Screws using a screwdriver.
-6 -
6.SPECIFICATIONS
1. | Image System |
|
| Image Device | 1/3 inch CCD image sensor |
| Pixel Elements | 768 (H) x 494 (V) |
2. | Electrical |
|
| TV System | NTSC |
|
| 2:1 Interlace, 15.734 kHz horizontal, 59.94 Hz vertical |
| Horizontal Resolution | 480 TV lines (typical) |
This camera is equipped with
This camera is able to clearly produce monochrome images at a range of less than 82 feet.
- 7 -
6. Environmental |
|
Operating Temperature | 14°F to 122°F |
and humidity | 20 % to 90 % RH |
Storage Temperature | |
and humidity | 90 % RH |
Design and specifications are subject to change without notice.
7. EXTERIOR VIEW
Condition | Check Points |
No image | • Are the camera and connected equipment turned on? |
| • Are wires connected correctly? |
Unnatural color | • Is the display monitor adjusted correctly? |
| • Is the lighting too dim? |
Flicker noise | • Under the fluorescent lamp of 60Hz, flicker noise rarely occurs. |
Defocusing at night | • Readjust the focus at |
| - 8 - |
LIMITED WARRANTY
CCD SECURITY CAMERA IK-7211A
The Imaging System Division (“ISD”) of Toshiba America Information Systems,Inc.makes the following limited warranties with regard to this CCD Camera Model
Three (3) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a period of three (3) years from the date of purchase by the Original
Instruction Manual (Owner's Manual) :You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product. Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the instructions to correct the problem.
How to Obtain Warranty Service
| S/N Ratio | 48 dB |
| Minimum Illumination | 0 lux (LED is ON) |
| Gain Control | AGC:High (30dB), Low(24dB) |
| White Balance | Auto |
| White Balance Range | 2,500 K to 9,500 K |
| Auto Electronic Shutter | 1/60 s to 1/100,000 s |
| Backlight Compensation (BLC) | ON / OFF |
| Video Output Signal | VBS (1.0 |
| Synchronization System | Internal |
| IR LED | 36 LEDs, 850nm |
| IR Distance | 82 feet (25m) |
3. | Mechanical |
|
| Weight | 1.4 lbs (630 g) camera only |
| Dimension | 3.2(W) x 3.1(H) x 5.4(D) inches (81.5mm(W) x 79.5mm(H) |
|
| x 137.5mm(D) (excluding protrusion and mounting bracket)) |
| Ingress Protection Rating | IP66 |
4. | Optical |
|
| f = | |
| View Angle of Lens | |
5. | Power |
|
| Input Voltage | 12V DC ±10 % |
3.1（79.5）
Ø2.8（Ø70） 3.2（81.5）
4.2（106）
5.4（137.5）
Ø2.4（Ø62） |
|
1（25） | |
| 120° |
120° |
|
| 2.1（54） |
0.24（6） |
|
1.Contact Toshiba America Information Systems, Inc. at (877)
2.If technical support determines that the unit is defective,an RMA will be issued with return instructions for repair.
3.Securely pack the Product in the original carton and external shipping pack, include a letter explaining the problem with a copy of the bill of sale or proof of purchase.
4.Prepay all transportation and insurance costs.
Your Responsibilities: This Limited Warranty is subject to the following conditions:
1.You must provide the bill of sale or proof of purchase at the time that warranty service is required.
2.You must notify Toshiba America Information Systems, Inc. at (877)
3.You must pack the Product in its original carton using the original packing material.Then insert the original carton containing the Product into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center.
DISCLAIMERS: ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT COMPANY, OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE, ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD'S WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD'S PRIOR AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD'S FACTORY SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY.
No person, agent, distributor,dealer,authorized service provider, or company is authorized to change, modify, or extend the terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the date
Current Consumption | 0.4A (MAX.) |
Dimensions: Inch (mm)
You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law.
Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives You spacific legal rights and You may also have other rights which vary from state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC1
Imaging Systems Division
- 9 - | - 10 - | - 11 - |