Specifications (DIN 45 500)
AMPLIFIER SECTION
Power output (at 240 V) |
| |
DIN 1 kHz (T.H.D. 1 %) | 2 x 100 W (6 Ω) | |
20 | ||
both channels driven | 2 x 80 W (6 Ω) | |
Total harmonic distortion |
| |
rated power at 20 | 0.09 % (6 Ω) | |
half power at 1 kHz | 0.03 % (6 Ω) | |
Power output at the DVD 6CH operation | ||
DIN 1 kHz (T.H.D. 1 %) |
| |
Front |
| 2 x 100 W (6 Ω) |
Center |
| 100 W (6 Ω) |
Surround |
| 2 x 100 W (6 Ω) |
Power bandwidth |
|
|
both channels driven, | 10 | |
Damping factor |
| 30 (6 Ω) |
Load impedance |
|
|
Front |
|
|
A or B |
| |
A and B |
| |
| ||
Center |
| |
Surround |
| |
Frequency response |
| |
PHONO | RIAA standard curve (30 | |
[For the United Kingdom] |
| |
CD, TAPE/MD, DVD, TV, VCR 1, VCR 2, VCR 3 | ||
|
| 10 |
[For Australia and New Zealand] |
| |
CD, TAPE, DVD, TV, VCR 1, VCR 2, VCR 3 | ||
|
| 10 |
Input sensitivity and impedance |
| |
PHONO |
| 3 mV/47 kΩ |
[For the United Kingdom] |
|
|
CD, TAPE/MD, DVD, TV, VCR 1, VCR 2, VCR 3 |
| |
|
| 200 mV/22 kΩ |
[For Australia and New Zealand] |
|
|
CD, TAPE, DVD, TV, VCR 1, VCR 2, VCR 3 | 200 mV/22 kΩ | |
S/N at rated power (6 Ω) (VGCA ON) |
|
|
PHONO | 70 dB (IHF, A: 80 dB) | |
[For the United Kingdom] |
|
|
CD, TAPE/MD, DVD (L/R/C/LS/RS), TV, VCR 1, VCR 2, VCR 3 |
113 dB (IHF A, rated power, S=2 V), 98 dB (IHF, A: 100 dB)
[For Australia and New Zealand]
CD, TAPE, DVD (L/R/C/LS/RS), TV, VCR 1, VCR 2, VCR 3
113 dB (IHF A, rated power, S=2 V), 98 dB (IHF, A: 100 dB)
Tone controls |
|
BASS | 50 Hz, +10 to |
TREBLE | 20 kHz, +10 to |
Output voltage |
|
[For the United Kingdom] |
|
TAPE/MD REC (OUT), VCR 1 OUT | 200 mV |
[For Australia and New Zealand] |
|
TAPE REC (OUT), VCR 1 OUT | 200 mV |
Channel balance (250 Hz– 6.3 kHz) | ±1 dB |
Channel separation | 55 dB |
Headphones output level and impedance | 430 mV/330 Ω |
Subwoofer frequency response | |
|
|
Digital input (OPTICAL) | CD, DVD, TV |
|
|
FM TUNER SECTION
Frequency range |
| ||
Sensitivity |
|
| |
| S/N 30 dB |
| 1.5 μV/75 Ω |
| S/N 26 dB |
| 1.3 μV/75 Ω |
| S/N 20 dB |
| 1.2 μV/75 Ω |
IHF usable sensitivity (IHF’58) |
| 1.5 μV/75 Ω | |
IHF 46 dB stereo quieting sensitivity | 22 μV/75 Ω | ||
Total harmonic distortion |
|
| |
| MONO |
| 0.2 % |
| STEREO |
| 0.3 % |
S/N |
|
| |
| MONO |
| 60 dB (75 dB, IHF) |
| STEREO |
| 58 dB (71 dB, IHF) |
Frequency response |
|
| |
| 20 |
| +1 dB, |
Alternate channel selectivity |
|
| |
| ±400 kHz |
| 65 dB |
Capture ratio |
| 1.5 dB | |
Image rejection at 98 MHz |
| 40 dB | |
IF rejection at 98 MHz |
| 70 dB | |
Spurious response rejection at 98 MHz | 70 dB | ||
AM suppression |
| 50 dB | |
Stereo separation |
|
| |
| 1 kHz |
| 40 dB |
Carrier leak |
|
| |
| 19 kHz |
| |
| 38 kHz |
| |
Channel balance (250 | ±1.5 dB | ||
Limiting point |
| 1.2 μV | |
Bandwidth |
|
| |
| IF amplifier |
| 180 kHz |
| FM demodulator |
| 1000 kHz |
Antenna terminal |
| 75 Ω (unbalanced) | |
| AM TUNER SECTION |
|
|
|
|
| |
Frequency range | |||
|
| ||
Sensitivity |
| 20 μV, 330 μV/m | |
Selectivity (at 999 kHz) |
| 55 dB | |
IF rejection (at 999 kHz) |
| 50 dB | |
| VIDEO SECTION |
| 1±0.1 |
|
| ||
Output voltage at 1 V input (unbalanced) | |||
Maximum input voltage |
| 1.5 | |
Input/output impedance |
| 75 Ω (unbalanced) | |
| GENERAL |
|
|
|
|
| |
Power supply |
| AC | |
Power consumption |
| 270 W | |
Dimensions (W x H x D) | |||
|
| ||
Mass |
| ||
|
|
| |
|
| ||
Power consumption in standby mode: | 2 W | ||
|
|
|
|
Notes:
1.Specifications are subject to change without notice. Mass and dimensions are approximate.
2.Total harmonic distortion is measured by the digital spectrum analyzer.
Matsushita Electric Industrial Co., Ltd. | En |
Osaka 542-8588, Japan
H0500HM0