Setting the Master flash
The modes available on the Master flash are TTL and M mode.
The master flash sets the signal transmission channel, flash reflector zooming position, flash mode of the master flash itself and flash mode and value adjustment of the Remote flash at A, B and C respectively.
In the main page
Select 
Wireless mode.
In the Wireless page
Select 
Master mode.
In the Master page
Netvigate the cursor and adjust the value according to the instruction at the bottom bar.
Cursor Netvigation
Value Adjust
Channel Select
Select Channel: Ch1, Ch2, Ch3 & Ch4
Zoom Select
Select Zoom Mode: Auto, 24mm, 28mm, 35mm, 50mm, 70mm, 85mm, 105mm
Single Group Slave Flash (Group A Setting)
1.Navigate the cursor to Group A
2.Navigate the cursor to Flash mode and select mode: TTL or M
Selecting TTL
1.Navigate the cursor to the Value Adjustment and set the EV compensation level.
2.Navigate the cursor to M (Master).
3.Select TTL or
4.When TTL mode selected, move the cursor to the Value Adjustment and set the EV compensation level.
5.Navigate the cursor to M (Master).
6.Select TTL or
7.When TTL mode selected, Navigate the cursor to the Flash Adjustment and set the power ratio.
Selecting M
1.Navigate the cursor to the Flash Adjustment and set the power ratio
2.Navigate the cursor to M (Master).
3.Select M or
4.When M mode selected, navigate the cursor to the Flash Adjustment and set the power ratio.
Note: When setting
Group Setting
Group
M = Master Flash
A = Group A
B = Group B
C = Group C
|
|
|
|
|
| Value Adjustment |
|
|
|
|
|
| Ev compensation at TTL mode |
|
|
|
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
| Power Ratio at M mode |
|
|
|
|
|
| |
|
|
|
|
|
| (1/1, 1/2, 1/4, 1/8, 1/16, |
|
|
|
|
|
| |
Flash Mode | 1/32, 1/64, 1/128) | |||||
TTL = TTL Mode |
| |||||
M = Manual Mode |
| |||||
| ||||||
camera’s shutter opens and is not be exposed in the actual picture.
Multiple Group Slave Flash (Group B & C Setting)
Group A MUST be set, in order to adding Group B
Adding Group B
When TTL mode selected in Group A
1.Navigate the cursor to GROUP B, and select TTL in the operation mode box.
27
28
2. | Navigate the cursor to Flash Adjustment and select the power level ratio |
| between Group A and Group B. |
| ^The power level ratio can be selected from 13 different combinations, such |
| as A:B = 8:1 – 5.6:1 – 4:1 – 2.8:1 – 2:1 – 1.4:1 – 1:1 – 1:1.4 – 1:2 – 1:2.8 – |
| 1:4 – 1:5.6 and 1:8 |
3. | Navigate the cursor to M (Master). |
4. | Select TTL or |
5. | When TTL mode selected, navigate the cursor to the Flash Adjustment and |
4.Select M or
5.When M mode selected, navigate the cursor to the Flash Adjustment and set the power ratio.
^This 3 group slave flash technology is recommended to shade off or remove the shadow behind subject which may be caused by the lighting produced by Group A and/or B.
set the EV Compensation. |
When M mode selected in Group A
1.Navigate the cursor to GROUP B, and select M in the operation mode box.
2.Navigate the cursor to Flash Adjustment and select the power ratio
3.Navigate the cursor to M (Master).
4.Select M or
5.When M mode selected, navigate the cursor to the Flash Adjustment and set the power ratio..
Adding Group C
Group A & B (A:B) MUST be set, in order to adding Group C.
^The group C is independently set out from the power ratio combination.
SETTING THE REMOTE FLASH
Group A
Master Flash
Group B
When TTL Mode selected in Group A & B:
1.Navigate the cursor to GROUP C, and select TTL in the Flash Mode.
2.Navigate the cursor to Flash Adjustment and select the EV compensation.
3.Navigate the cursor to M (Master).
4.Select TTL or
5.When TTL mode selected, navigate the cursor to the Flash Adjustment and set the EV Compensation.
When M Mode selected in Group A & B:
1.Navigate the cursor to GROUP C, and select M in the Flash Adjustment.
2.Navigate the cursor to Flash Adjustment and select the power ratio.
3.Navigate the cursor to M (Master).
29
Group C
CREATIVE FLASH LIGHTING: Set Master flash.
Set Slave flash/ flashes.
Make sure the channel and its group setting are correct.
Attach the Master flash to the camera and place the Slave flash/ flashes at any desirable place within the system operation area, which is approximately 7 to 10 meters between the Master and Slave flash/ flashes depending on the setting condition.
30