Ashly PE Series manual Spec Table, PE-800 PE-1200 PE-1800 PE-2400 PE-3000 PE-3800

Page 10

Page - 10

Operator Manual – PE Series Amplifiers

 

 

 

Important Safety

Instructions – 2

Introduction - 3

The PE Series - 4

Physical Description - 5

Installation – 6

Operation – 8

Troubleshooting - 9

Spec Table - 10

Measurements - 11

Dimensions - 12

Warranty - 13

Spec Table

 

 

PE-800

 

PE-1200

 

PE-1800

 

PE-2400

PE-3000

 

 

PE-3800

Power Output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stereo Mode, both channels driven

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 ohms, 20 Hz - 20 kHz, 1% THD

200 W

 

300 W

 

 

500 W

 

700 W

900 W

 

 

1,100 W

4 ohms, 20 Hz - 20 kHz, 1% THD

400 W

 

600 W

 

 

900 W

 

1,200 W

1,500 W

1,900 W

Bridged Mono Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 ohms, 20 Hz - 20 kHz, 1% THD

800 W

 

1,200 W

 

1,800 W

 

2,400 W

3,000 W

 

 

3,800 W

Parallel Mono Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 ohms, 20 Hz - 20 kHz, 1% THD

800 W

 

1,300 W

 

1,800 W

 

2,400 W

3,000 W

3,800 W

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal to Noise (20 Hz-20 kHz,

>98 dB

 

>105 dB

 

>108 dB

 

>110 dB

>111 dB

 

 

>112 dB

unweighted):

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Voltage Gain:

 

 

 

 

 

 

 

 

26 dB, 32 dB or 1.5 V sensitivity (selectable)

Output Circuitry:

Bipolar, Class AB

Bipolar, Class AB

Bipolar, Class H

Bipolar, Class H

Bipolar, Class H

 

Bipolar, Class H

Power Requirements (1/8 Power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pink Noise @ 4 Ohm):

420W

 

640W

 

 

611W

 

790W

1010W

 

1220W

All Models

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Distortion (SMPTE, typical) - 8 ohm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

load, 10 dB below rated power

 

 

 

 

 

 

 

 

 

 

 

 

<.01%

Distortion (THD+N, typical) - 8 ohm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

load, 10 dB below rated power, 20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hz - 10 kHz

 

 

 

 

 

 

 

 

 

 

 

 

<.01%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frequency Response

 

 

 

 

 

 

 

 

 

20 Hz - 20 kHz, +/- 0.15 dB

Damping Factor - 8 ohm load, < 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

kHz

 

 

 

 

 

 

 

 

 

 

 

 

> 400

Input Impedance

 

 

 

 

 

 

 

 

 

20 kOhm, balanced

Maximum Input Level:

 

 

 

 

 

 

 

 

 

 

 

 

 

+21 dBu

Input Clipping

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cooling

 

 

 

 

 

 

 

 

temperature dependent speed-controlled axial fan

Control Network:

 

 

 

 

 

 

onboard, compatible with standard 100 MB Ethernet hardware

Front Panel Indicators

 

 

 

 

 

 

Per channel: Clip, -6 dB, -12 dB, -18 dB, Temp, Output current.

 

 

 

 

Overall: power, standby, protect, bridged mono, parallel mono, communications

Attenuators:

 

 

 

 

 

 

 

Per channel: front panel, software, offset and remote

Input Connectors, each channel

 

 

 

 

 

 

 

 

XLR female/TRS, Euroblock, XLR male (looping)

Output connectors, each channel

 

 

 

 

 

 

 

Speakon, screw terminals (Model 800 and 1200 only)

Amplifier Protection

inrush current limitation, temperature monitoring heat-sinks, output DC protection, power transistor

 

 

 

 

 

 

 

SOA protection, output over-current protection, mains fuses protection

Load Protection

 

 

 

 

 

 

 

 

 

Adjustable clip limiter

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Cable Connector

15A Edison

 

 

 

 

20Amp

 

 

30A Twistlock

Dimensions

 

 

19"W x 3.5"H x 15.5"D (483mmW x 88.9mmH x 394mmD)

 

 

Weight

22 lbs. (9.98kg)

 

 

23 lbs. (10.43kg)

24 lbs. (10.89kg)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optional ProteaNE/DSP Input Card

 

 

 

 

 

 

Latency

 

 

 

 

Analog - 1.512 ms at 48KHz sampling.

 

 

 

 

 

 

 

 

 

 

 

Digital - 0.784 ms at 96KHz sampling.

 

 

 

 

 

 

A/D, D/A Converters:

 

 

 

 

24-bit

 

 

 

 

 

 

 

 

DSP

 

 

 

 

32-bit, floating-point

 

 

 

 

 

 

 

 

Digital Input Type

 

 

 

 

AES3, 16-24 bit, 44.1 to 96 kHz.

 

 

 

 

 

 

Signal Flow Architecture

 

 

 

"Click and hot plug" flexible architecture, non-compiling

 

 

 

Available Processing Blocks

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Equalization

 

Parametric, Notch, Graphic, Shelving, HPF/LPF, All pass

 

 

 

 

 

Signal Delay

 

Up to 967msec any input/output

 

 

 

 

 

 

 

 

HPF/LPF

 

Up to 8th order (48 dB/octave)

 

 

 

 

 

 

Compressor/Limiter, Gate, Meter

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal Generator

 

Pink noise, White Noise, Sine Wave

 

 

 

 

 

 

 

 

Level Control

 

With or without VCA-type subgrouping

 

 

 

 

 

All Specifications Subject to Change or Improvement Without Notice.

Copyright© 2007 – Ashly Audio Inc.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Ashly Audio Inc PE-Series AmplifierOperator Manual PE Series Amplifiers Manuel d’instruction et observez les consignesAbout Ashly FCC CompliancePE Series ProtectionAmplifier Front Panel Physical DescriptionAmplifier Rear Panel Input Module InstallationRequirements Connectors & Polarity Operator Manual PE Series Amplifiers Typical ApplicationsBridged Mono Mode Channel Stereo ModeParallel-Mono Mode OperationTroubleshooting Situation Indication ActionSpec Table PE-800 PE-1200 PE-1800 PE-2400 PE-3000 PE-3800Phase vs. frequency, Ch1, Ch2 MeasurementsAmplifier Dimensions Remote Level & Power ConnectionsLimited Warranty Obtaining Warranty Service

PE Series specifications

The Ashly PE Series is renowned in the audio industry for its exceptional performance, versatility, and reliability. Designed for professional audio applications, the PE Series amplifiers deliver powerful sound quality, making them suitable for live sound, installations, and event productions.

One of the standout features of the Ashly PE Series is its advanced Class D amplification technology. This technology not only enhances efficiency but also ensures that the amplifiers remain lightweight and manageable, making them an ideal choice for touring and mobile setups. The PE Series offers a range of power options, from modest wattage to high-output models, catering to various needs and scenarios.

Another significant characteristic of the PE Series is the incorporation of Ashly's proprietary DSP capabilities. The built-in digital signal processing allows users to optimize audio performance through customizable equalization, limiting, and crossover functions. This flexibility helps users fine-tune their sound systems to achieve the desired audio quality, whether in a small venue or a large concert environment.

The PE Series amplifiers also feature a rugged and durable design, built to withstand the rigors of touring and installation. With sealed enclosures, high-quality components, and a robust cooling system, these amplifiers are engineered for longevity and consistent performance. The intuitive front panel controls and clear LED indicators provide users with essential information at a glance, facilitating ease of use for sound engineers and operators.

Connectivity is another strength of the Ashly PE Series. The amplifiers come equipped with multiple input options, including balanced XLR and TRS connectors, enabling seamless integration with various audio sources. Additionally, the units include Speakon and binding post output connectors, ensuring compatibility with a broad range of loudspeakers.

In summary, the Ashly PE Series amplifiers embody the perfect blend of power, flexibility, and durability. With advanced Class D technology, integrated DSP capabilities, and robust construction, these amplifiers meet the demands of diverse audio environments. Whether for live events, installations, or studio applications, the Ashly PE Series stands out as a reliable choice for professionals seeking high-quality audio performance.
Top Page Image Contents