Ashly NE800 manual DSP Specifications

Operating Manual - NE Two Channel Power Amplifiers

Distortion (SMPTE, typical) - 8 ohm load, 10dB below rated power: . . . . . . . . . . . . . . . <0.5%

Distortion (THD-N, typical) - 8 ohm load, 10dB below rated power, 20Hz-20kHz: . . . . . <0.5%

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz-20kHz, +/-1dB Damping Factor (8 ohm load, <1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >250

Input Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20K Ohm, balanced Maximum Input Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +21dB

Cooling	. . . . .	temperature dependent speed-controlled axial fan
Control Network . .	. . . . .	onboard, compatible with standard 100MB Ethernet hardware
Front Panel Indicators . . per channel: Clip/Mute, -6dB, -12dB, -18dB, Temp, Current, Bridge
		overall: Power, Standby, Protect, Power Switch Disable, Com
		Control Surface and Amp LEDs: Level meters are dB below RATED output
Attenuators:		per channel: front panel, software, offset link group, and remote
Input Connections	. . . . . XLR Female /Euroblock
Analog Aux Outputs	. . . . XLR Male / Euroblock
Output Connections	. . . . Speakon / Euroblock
Remote Standby . .	. . . . .	Euroblock
Remote Level Control . . .		Euroblock
Amplifier Protection		inrush current limitation, temperature monitoring, output over-current protection, mains fuses
Power Cable Connector		15A Edison
Dimensions	. . . . .	19”W x 3.5”H x 15.5”D (483 x 89 x 394mm)
Weight	. . . . .	21 lbs (9.53kg)
Environmental: . . .	. . . . .	40-120 deg. F, (4-49 deg, C) noncondensing

DSP SPECIFICATIONS

Input:	. . . Active Balanced, 10 kohms	Ducker
Max Input Level: . . .	. . . +21 dBu	Ducking Type:	high/low priority trigger,
DYNAMICS		. . . . . . . . . . . . . . . . . . . .	filibuster, ducked program
		Trigger Threshold: . . . . . -80dBu to +20 dBu
Brick Wall Limiter		Ducking Release:	5ms/dB to 1000ms/dB
Threshold:	. . . -20dBu to +20dBu	Ducking Depth:	0dB to -30dB
Ratio:	. . . infinite
Attack:	. . . 0.2ms/dB to 50 ms/dB	Gate
Release:	. . . 5ms/dB to 1000ms/dB	Threshold:	-80dBu to +20dBu
Compressor		Range:	off, 100dB to 0dB
		Attack:	0.2ms/dB to 50 ms/dB
Threshold:	. . . -20dBu to +20dBu	Release:	5ms/dB to 1000ms/dB
Ratio:	. . . 1.2:1 to infinite
Attack:	. . . 0.2 to 50ms	GAIN
Release:	. . . 5ms/dB to 1000ms/dB	Gain:	off, -50dB to +12dB
Detector:	. . . Peak/Average	Gain w/VCA:	off, -50dB to +12dB
Autoleveler		WR-5 Remote Gain: . . . . off, -50dB to +12dB
Target Level:	. . . -40dBu to +20dBu	EQUALIZATION
Action:	. . . gentle, normal, aggressive,	31 Band Graphic
	user defined	Filter Type:	constant Q or proportional Q
Maximum Gain: . . . .	. . . 0dB to +22dB	Bandwidth:	0.499oct to 0.25oct
Ratio:	. . . 1.2:1 to 10:1
Threshold Below Target: -30dB to 0dB
Gain Increase Rate: . . . . 5ms/dB to 1000ms/dB
Gain Decrease Rate:	. . . 5ms/dB to 1000ms/dB
Hold Time:	. . . 0-6 sec

11