
Page - 10  | Operator Manual – SRA Series Amplifiers | |
  | 
  | 
  | 
Important Safety
Instructions – 2
Introduction - 3
The SRA Series - 4
Physical Description - 5
Installation – 6
Operation – 8
Troubleshooting - 9
Spec Table - 10
Dimensions - 11
Warranty - 12
Spec Table
  | 
  | 
 | |||
Power Output Per Channel  | 
  | 
  | 
  | 
  | 
  | 
Stereo Mode, all channels driven  | 
  | 
  | 
  | 
  | 
  | 
8 ohms, 20 Hz - 20 kHz, 1% THD  | 2 x 40W  | 4 x 40W  | 2 x 80W  | 
  | 4 x 80W  | 
4 ohms, 20 Hz - 20 kHz, 1% THD  | 2 x 75 W  | 4 x 75 W  | 2 x 150 W  | 
  | 4 x 150 W  | 
Bridged Mono Mode | 
  | 
  | 
  | 
  | 
  | 
8 ohms, 20 Hz - 20 kHz, 1% THD  | 1 x 150 W  | 2 x 150 W  | 1 x 300 W  | 
  | 2 x 300 W  | 
  | 
  | 
  | 
  | 
  | 
  | 
Signal to Noise (20   | >98 dB  | >98 dB  | >105 dB  | 
  | >105 dB  | 
Voltage Gain:  | 
  | 
  | 26 dB, 36 dB sensitivity (selectable)  | ||
Output Circuitry:  | Class D  | Class D  | Class D  | 
  | Class D  | 
Power Consumption (Pink Noise @ 4 Ohm):  | 
  | 
  | 
  | 
  | 
  | 
1/8th Output  | 18.75W  | 37.5W  | 37.5W  | 
  | 75.0W  | 
1/8th Draw  | 39.0W  | 74.0W  | 64.0W  | 
  | 125W  | 
1/8th Current  | 0.69A  | 1.24A  | 1.10A  | 
  | 1.98A  | 
Idle Power  | 17.0W  | 30.0W  | 20.0W  | 
  | 36.0W  | 
Idle Current  | 0.30A  | 0.52A  | 0.35A  | 
  | 0.62A  | 
  | 
  | 
  | 
  | 
  | |
Frequency Response  | 
  | 
  | 20 Hz - 20 kHz, +/- 1.0 dB  | ||
Damping Factor - 8 ohm load, < 1 kHz  | 
  | 
  | 
  | 
  | > 200 into 8  | 
Input Impedance  | 
  | 
  | 
  | 
  | 20 kOhm, balanced  | 
Maximum Input Level:  | 
  | 
  | 
  | 
  | +21 dBu  | 
Input Impedance  | 
  | 
  | 
  | 
  | 20k balanced  | 
Cooling  | 
  | 
  | 
  | 
  | Convection  | 
Front Panel Indicators per channel  | 
  | 
  | 
  | 
  | Clip & Signal  | 
Front Panel Indicators overall  | 
  | 
  | 
  | power, standby, protect  | |
Attenuators  | 
  | 
  | 
  | Per channel: front panel  | |
Input Connectors, each channel  | 
  | 
  | 
  | 
  | 3- Pin Euroblock  | 
Output connectors, each channel  | 
  | 
  | 
  | 
  | Screw terminals  | 
Amplifier Protection  | 
  | Output Overcurent, DC Output, Mail Supply Rail Overvoltage  | |||
  | 
  | Chassis Temperature, Inrush Limiting, Mains Fuse  | |||
Power Cable Connector  | 
  | 
  | 
  | 
  | |
Dimensions  | 
  | 
  | 
  | 
  | 19” x 1.75” x 11”  | 
Weight  | 9.0 lbs  | 10.0 lbs  | 9.0 lbs  | 
  | 10.0 lbs  | 
All Specifications Subject to Change or Improvement Without Notice.
Copyright© 2006 – Ashly Audio Inc.