Vivotek FD6122V, FD6112V manual Hardware Installation, Ethernet Connection

Page 8

Installation

Hardware Installation

Please verify that your product package contains all the accessories listed in the foregoing Package Contents. Depending on the user’s application, an Ethernet cable may be needed. The Ethernet cable should meet the specs of UTP Category 5 and not exceed 100 meters in length.

Connect the power adapter jack to the Network Camera before plugging in to the power socket. This will reduce the risk of accidental electric shock.

Upon powering up, the device runs through a self-test procedure and the LEDs will blink between green and red for a few times. If self-test passes, the green LED will shut off while the red LED is constantly on and the Network Camera will be on stand-by and ready for software installation. If self-test fails the red LED will blink several times. Refer to Appendix A for troubleshooting.

Ethernet Connection

Make sure the Ethernet is firmly connected to a switch hub; then, plug in the power adapter. If the LED turns out to be steady green after self-test, go to next paragraph “Software Installation”.

The Network Camera provides a general I/O terminal block with one digital input and one relay switch for device control. Pin 3 and Pin 4 can be connected to an external sensor device and the state of voltage can be monitored from the initial state 'LOW'. The relay switches Pin 1 and Pin 2 can be used to turn on or off an external device.

- 4 -

www.vivotek.com

T: 886-2-82455282

F: 886-2-82455532

Image 8

Contents Page Technical@vivotek.com Sales@vivotek.com Before You Use This Product Package Contents Table of Contents Smtp FTP Appendix886-2-82455282 886-2-82455532 Hardware Installation Ethernet ConnectionMount the Camera 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Software Installation 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Initial Access to the Network Camera Installing Plug-inCheck Network Settings Add Password to Prevent Unauthorized AccessHow to Use AuthenticationPrimary User’s Capabilities Main Screen with Camera ViewConfiguration Camera viewClient Settings Both886-2-82455282 886-2-82455532 Administrator’s Capabilities Fine-tuning for Best PerformanceFor Best Real-time Video Images Only Quality Images Will DoSomewhere Between Real-time and Clear Images Select for Motion JpegProtect Network Camera by Passwords Opening Accounts for New UsersDemo on Multiple Sites Mid-scale Service Product Demo for E-business Large-scale ServiceBuild a Multimedia Web Attraction Site More Flexible Options for ViewersIf the web space has FTP service If the web space has no FTP service Image URL Build a Security Application Send Snapshots When Motion is Detected 886-2-82455282 886-2-82455532 Definitions in Configuration System Parameters User Group Administration 886-2-82455282 886-2-82455532 Edit User Network Settings GeneralHttp Streaming886-2-82455282 886-2-82455532 Ddns & UPnP 886-2-82455282 886-2-82455532 Mail & FTP Smtp886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Video Codec Parameters 886-2-82455282 886-2-82455532 Image Settings Contrast, HueCamera Settings Audio 886-2-82455282 886-2-82455532 Motion Detection 886-2-82455282 886-2-82455532 Event Operation Application SetupWeekly Schedule Sequential Operation Naming rule of snapshot file FTP886-2-82455282 886-2-82455532 Viewing System Parameters Factory DefaultViewing System Log Troubleshooting AppendixSoon as the second self-diagnostic starts Frequently Asked Questions 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Style convention URL commands of Network CameraOverview Method GET/POST General CGI URL syntax and parametersGet server parameter values Example request IP address and it’s response Set server parameter values NosyncWirelessNetwork Camera With Pan/Tilt/Zoom Available parameters on the serverHhmmss Skip to invoke default serverYyyy/mm/dd Blank 192.168.0.99 255.255.255.0Than 40 characters Mailto2 Text String 120 50035002 384000 For Ntsc only8000 Save Directly save the adjust image Parameters Group CCD Ntsc & Cmos Application page CGI command Script.vssxMethod GET/POST Sun Dihigh Drive the digital output Query status of the digital inputQuery status of the digital output Capture single snapshot Account management System logs Privilege=dido&privilege=listenConfiguration file System Information Preset Locations Technical Specifications NetworkingTechnology License Notice Electromagnetic Compatibility EMC