Vivotek IP6127, IP6117 manual Hardware Installation, To install in Ethernet

Page 8

Installation

Hardware Installation

Please verify that your product package contains all the accessories listed in the foregoing Package Contents. Depending on the user’s application, an Ethernet cable may be needed. The Ethernet cable should meet the specs of UTP Category 5 and not exceed 100 meters in length.

Connect the power adapter jack to the Network Camera before plugging in to the power socket. This will reduce the risk of accidental electric shock.

Upon powering up, the device runs through a self-test procedure and the front LEDs will blink between green and red for a few times. If self-test passes, the LEDs will shut off and the Network Camera will be on stand-by and ready for software installation. If self-test fails the red LED will blink several times. Refer to Appendix A for troubleshooting.

The Network Camera will first detect Ethernet. If it does not connect to Ethernet, the Network Camera will try WLAN. During the searching and connecting process to the wireless access point or station, the LED of the Network Camera will keep red. Until the Network Camera is connected to the other wireless device, the LED will become green and flash. Operating in either network mode, the green LED will flash every second as heartbeat to indicate alive.

To install in Ethernet

Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet cable plug in the power adapter. If the LED turns out to be steady green after

www.vivotek.com

T: 886-2-82455282

F: 886-2-82455532

Image 8

Contents Page Technical@vivotek.com Sales@vivotek.com Before You Use This Product Package Contents Table of Contents Http Appendix Hardware Installation To install in EthernetTo install in wireless LAN Software Installation 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Initial Access to the Network Camera Installing Plug-inCheck Network Settings Add Password to Prevent Unauthorized AccessHow to Use AuthenticationPrimary User’s Capabilities Main Screen with Camera ViewConfiguration Camera viewClient Settings Both886-2-82455282 886-2-82455532 Administrator’s Capabilities Fine-tuning for Best PerformanceFor Best Real-time Video Images Only Quality Images Will DoSomewhere Between Real-time and Clear Images Select for Motion JpegProtect Network Camera by Passwords Opening Accounts for New UsersDemo on Multiple Sites Mid-scale Service Product Demo for E-business Large-scale ServiceBuild a Multimedia Web Attraction Site More Flexible Options for ViewersIf the web space has FTP service If the web space has no FTP service Image URL Build a Security Application Send Snapshots When Motion is Detected 886-2-82455282 886-2-82455532 Definitions in Configuration System Parameters User Group Administration 886-2-82455282 886-2-82455532 Edit User Network Settings GeneralHttp Streaming886-2-82455282 886-2-82455532 Wireless耟 886-2-82455282 886-2-82455532 Ddns & UPnP 886-2-82455282 886-2-82455532 Mail & FTP Smtp886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Video Codec Parameters 886-2-82455282 886-2-82455532 Image Settings Contrast, HueCCD Settings Audio 886-2-82455282 886-2-82455532 Motion Detection 886-2-82455282 886-2-82455532 Event Operation Application SetupWeekly Schedule Sequential Operation Naming rule of snapshot file FTP886-2-82455282 886-2-82455532 Viewing System Parameters Factory DefaultViewing System Log Troubleshooting AppendixFrequently Asked Questions 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Style convention URL commands of Network CameraOverview Method GET/POST General CGI URL syntax and parametersGet server parameter values Example request IP address and it’s response Set server parameter values NosyncWirelessNetwork Camera With Pan/Tilt/Zoom Available parameters on the serverHhmmss Skip to invoke default serverYyyy/mm/dd Blank 192.168.0.99 255.255.255.0Than 40 characters Mailto2 Text String 5003 5002 Group Wireless restartDefault Auto ShortOpen 0000000000120 384000 For Ntsc only8000 Save Directly save the adjust image Parameters Group CCD Ntsc & Cmos Enable Enable or disable the Upnp service Group App Application page CGI command Script.vssxSun Fri Resetdo Drive the digital outputQuery status of the digital input Query status of the digital output Account management Capture single snapshotEdit Privilege=dido&privilege=listenConfiguration file System logsSystem Information 886-2-82455282 886-2-82455532 Technical Specifications FeaturesTechnology License Notice MPEG-4 Visual TechnologyElectromagnetic Compatibility EMC Liability