AGFA DC-830i operating instructions Troubleshooting, Problem Cause Solution

Page 51

Troubleshooting

Problem

Cause

Solution

Power does not turn on.

Battery is inserted in the wrong

Reload battery in the correct

 

direction.

direction.

 

 

 

 

Batteries are dead.

Replace or recharge batteries.

 

 

 

 

The battery compartment door

Make sure the battery

 

is open.

compartment door is securely

 

 

closed.

 

 

 

The camera does not take

The flash is charging.

Wait for the flash to charge.

pictures.

 

 

Memory is full.

Insert a new memory card.

 

 

 

 

Memory card is not formatted

The card may be defective,

 

correctly.

use a new card.

 

 

 

Image is not recorded when

The Flash is charge.

Wait for the flash to charge.

the shutter button is pressed.

 

 

Memory is full.

Insert a new memory card.

 

 

 

The flash does not fire.

Flash is set to OFF.

Set the flash to any mode

 

 

except off.

 

 

 

Image is blurry or out of focus.

The camera was moving when

Hold the camera steady when

 

the image was captured.

shooting picture.

 

 

 

 

The subject was beyond the

Turn the Macro mode on it the

 

range within which the camera

subject is within 15 cm or 40

 

can focus.

cm.

 

 

Do not use Macro mode when

 

 

shooting distant subjects.

 

 

 

Image is not displayed on the

A memory card with non-DCIF

This camera cannot display

LCD monitor.

images (recorded with other

non-DCIF images.

 

camera) is loaded.

 

 

 

 

Recorded images are not

The camera was turned off /

If the battery low indicator

saved in memory.

powered down before the

appears on the LCD monitor,

 

image was stored in memory.

replace the battery

 

 

immediately.

 

 

 

Cannot transfer images to a

USB driver is not installed.

Install the USB driver before

computer after connecting the

 

you connect the camera to a

USB cable.

 

computer / turn the camera on.

 

 

 

Card error

The memory card format may

Re-format the memory card to

 

not be correct.

the FAT format using a card

 

 

reader in Windows.

 

 

 

47

Image 51
Contents Precautions Extending battery lifeDisclaimer Page Iii ContentsMaking Connections Getting Started Using This MenuContent Parts of the Camera Page Low Battery Indicator About Battery TypeInserting the Batteries DCF Protocol Inserting the Memory CardInsert the card About Camera MemorySetting the Display Language / Date & Time Setting the Display LanguageSetting the Date & Time Apply the setting REC mode Using the LCD MonitorDpof Playback mode„ REC mode „ Playback modeChanging the LCD Status Basic Operation Turning the Power On and OffPress the Power button n again to turn the power off Power Saving FunctionSet the camera to the REC mode Launch the mode palette Changing the ModeSwitching between REC mode and Playback mode Selecting the REC modePage Select an item Using the MenusChange the setting REC menuSetup menu Open the Setup menuREC menu list Movie Beep Press the Menu n button to close the menu Setup menu listVolume ShutterAlkaline ResetPAL Computer / PrinterTake a picture Basic RecordingRecording Still Images Half press the shutter button to focus the imageUsing the Q mode Setting Image Size and Quality Resolution ValuesQuality Values Using the Zoom Function Using the Flash Using the Macro Burst Using the Self-timer & BurstSec 10 secFinish recording Setting the Movie SizeRecording Movie Clips Start recordingPlaying Back Audio Clips Recording Audio ClipsPlaying Back a Voice Memo Recording a Voice MemoOpen the Playback menu Press the SET button to start recording for 30 secondsSetting the Metering Setting the White BalanceOther Recording Functions Setting the Highlight Setting the ISOSetting the Exposure Setting the AEBSetting the Sharpness Setting the Photo EffectSetting Date Stamp Press the four-way control Turn the power on, and set the camera to the Playback modePlayback Playback ImagesSave the image Magnifying & Trimming Still ImagesMagnify the image Trim the imagePlaying a Slide Show Viewing in ThumbnailDeleting Files Deleting a Single FileOpen the menu Delete images Deleting Multiple FilesPress or to select Select, and then press the SET button Select multiple imagesPress To select Lock all, and then press the SET button To the Playback modeProtecting a Single File Protecting All FilesProtect images Protecting Multiple FilesChanging the Image Size Editing ImagesRotating Still Images Press the SET button to rotate the imagePress or to select an option, and then press the SET button Changing the Image with EffectsPress To select Single, then press the SET button Copying the FilesBe sure you have inserted a memory Card into your digital camera. SetPrint the date stamp out Setting the DpofChoosing a Startup Image Connecting the Camera to a TV Making ConnectionsDisplay on TV Connecting the Camera to a PC Using the Card ReaderConnecting the Camera to a Computer with the USB Cable File Naming AppendixAbout the Folder & File Name Folder StructureProblem Cause Solution TroubleshootingNtsc / PAL SpecificationsFunction Available List Mode Still Capture FunctionISO Page Customer care Service & Repair Hotline EuropeService & Support Hotline Germany Online Service / International contactFCC Compliance and Advisory