Arcam AV888, AVR600, AVR500 manual Av, Sat, Dvd

Page 17

HDMI

AV

SAT

DVD

VCR

PVR

OUT 2

OUT 1

HDMI connectors

AV, SAT, DVD, VCR, PVR

Connect the HDMI video outputs of your source equipment to these corresponding HDMI inputs.

OUT 1

Connect this output to the HDMI video input of your main zone display device.

OUT 2

Connect this output to the HDMI video input of your second display device or to another HDMI display device in a second living space. As the unit has only one processed video path, this signal will be a copy of the signal on Out 1.

VCR

PVR

AV

SAT

DVD

Zone 2 connectors

Z2 AUDIO OUT, Z2 VIDEO OUT

Connect these analogue audio and video outputs to your Zone 2 equipment. See ‘Multi- room Setup’ on page 50 for information.

S-Video and Composite connectors

VCR, PVR

Connect these inputs to the S-Video and Composite outputs of your available source equipment.

English

NOTE

All Zone 1 analogue video outputs will be disabled if an HDMI digital video source is selected.

Component/RGB video connectors

These inputs are suitable for connection to source devices which output Component (YUV or YPbPr) or RGB high quality analogue video signals. These signals are usually available from DVD players, set-top boxes or games consoles.

If you are connecting up to an RGB source you will also need to connect the source’s Composite output to the unit’s Composite input to act as a video sync. The Composite signal should be on the same named input as the RGB signals.

RGB video outputs on source equipment are often on SCART connectors. You will need to use a SCART to ‘RGB+Sync on phono’ breakout cable, available from your Arcam dealer.

NOTE

When setting up the menus (later in this manual), you will need to select whether the three-wire high quality video input is Component or RGB for each input. This is done on the ‘HQ Video In’ line in the Input Config menu. Failure to do this can result in a green looking picture or a picture that is unstable.

AV, SAT, DVD

Connect the Component video outputs of your source equipment to these inputs.

OUT

Connect this output to the Component video input of your display device.

NOTE

Analogue RGB video output is not available from the AVR500. The analogue three-wire high quality video output is always configured as Component video.

E-15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents N d b o o k AVR surround amplifier / AV processor AVR500 / AVR600 / AV888Important safety instructions Safety GuidelinesSafety compliance Class II productRespect des consignes de sécurité Class II produitInstructions de sécurité importantes Page Professional Installation? ContentsDIY setup? WelcomeBefore you Begin… Standby power PowerPlacing the unit Interconnect cablesTrademark acknowledgements Making connections GeneralProduct differences and options Component/RGB Video CompositeAVR600 AV888 Zone 3 connectors Hdmi connectorsComponent/RGB video connectors Zone 2 connectorsDigital audio Phono Analogue audio ConnectorsTape inputs MCH inputInfra-red IR connectors Trigger connectorsSatellite receiver DVD playerCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Component, S-Video and Composite connectors, see Video connectorsAVR500 Aerials, control and communicationAV, SAT, DVD Front panel Phones socket For more information on connecting speakers, see page 18Subwoofer outputs Trigger connectors Preferred video hook-up, in order of preference is VCR, Camcorder, Games Console etcConnecting an iPod using the Arcam rDock Sirius Radio ConnectorsAerial connectors AVR500/AVR600 only Connecting an aerial Data connectors Network connectors USB connector Other ConnectorsRS232 serial connector RLead/rDockConnecting subwoofers Connecting speakers AVR500 & AVR600Speakers Speaker cablesSubwoofer CentreFront left and right Surround left and rightOperation Switching onOperating your AVR500 /AVR600 / AV888 Selecting a sourceExtended front panel menu Using Zone 2Updating firmware using a PC Front panel Operation Using the remote control CR102 universal remote controllerInserting batteries into the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesOK selects/play the highlighted file AMP AMP Device ModeIPod commands DVD DVD Device Mode TUN TUN Device ModeNetwork commands Highlighted menu on the screenMenus SAT SAT Device ModeAV AV Device Mode VCR VCR Device Mode PVR PVR Device ModeStarts Program mode CD CD Device ModePlay Clears programmed itemSpeaker types Essential SetupSpeaker Distances Speaker LevelsAuto speaker setup Auto speaker SetupProblems Using a subwooferNavigating the setup menu Setup menusSelecting the audio source software version 1.9 + Selecting the video sourceTypes To navigate down to the Video Source optionTreble Bass Input ConfigGeneral information and system controls General SetupPlii Dimension Plii Centre Width Plii Panorama Spkr Types Auto SetupSpkr Distance Spkr LevelsVideo Outputs Video InputsProgressive scan playback Important points to rememberMode Zone SettingsNetwork For Stereo sourcesEnglish Two-channel source modes Decoding ModesIntroduction Decoding modes Multichannel source modesVolume Leveller SettingsDolby Volume is a sophisticated new Calibration OffsetEnglish Saving and selecting Presets Tuning/Channel SelectionDeleting Presets Tuner OperationDefault unlock code is Sirius errorsOperation Locking ChannelsSelecting the playback source Network/usb OperationUSB playback Internet radio stationsAnalogue pre-amplifier outputs AVR600/AV888 only External AmplifiersEnglish XLR balanced line outputs AV888 only SW2, SW3Zone Multi-room Set upZone 3 AVR600/AV888 only Zone 2 and 3 control outputsZone English Multi-room connection guideCode Learning Customising CR102Key Mover Volume punch-throughCreating Macros Locking/Unlocking a specific Device Mode Mode MoverTo restore a moved Device Mode key to its original state Copy a key between Device ModesResetting the CR102 Mode key IR punch-throughProblem Check that When I turn on Volume is always too loudSwitched off Wired networkContinual improvement policy SpecificationsWorldwide Guarantee Product GuaranteeClaims under guarantee Problems?Device code Tables ICE HCMIRT ITCSBR RFTSEG SEIGPX AVPKEC KLHNTL ADBUPC DKKCGV CATDCE ENGSKY+ AsciTPS UECYES SH222E Issue B
Related manuals
Manual 74 pages 35.94 Kb Manual 68 pages 17.1 Kb Manual 68 pages 27.09 Kb

AV888, AVR500, AVR600 specifications

The Arcam AVR600 is a high-performance AV receiver that is designed for audiophiles and home cinema enthusiasts who seek a premium audio and video experience. This receiver stands out with its array of features and technologies that elevate sound quality and user experience.

At the heart of the AVR600 is its high-fidelity amplification system. The receiver is equipped with a robust 7-channel amplification setup, delivering a total output of 120 watts per channel into 8 ohms. This power enables the AVR600 to reproduce dynamic audio with precision, whether it be for movies, music, or gaming. The class G amplifier design offers exceptional efficiency and reduces distortion, ensuring that sound remains clean and focused even at higher volumes.

The AVR600 boasts extensive connectivity options to accommodate various audio and video sources. It features multiple HDMI inputs and outputs supporting 3D video and 4K scaling, providing flexibility for connecting modern devices. The unit also includes analog and digital inputs, a dedicated phono input for vinyl enthusiasts, and support for multi-room audio setups. With its built-in Bluetooth and network streaming capabilities, users can easily access high-resolution audio files from their digital libraries or popular streaming services.

One of the key technologies in the AVR600 is its advanced room correction system, known as Dirac Live. This sophisticated calibration tool analyzes the acoustics of the room and automatically adjusts the output of the receiver to compensate for any sound anomalies. As a result, listeners experience optimized sound tailored to their specific environment, enhancing the overall listening experience.

For video performance, the AVR600 supports a range of formats, including Dolby Atmos and DTS:X, ensuring an immersive home theater experience with enveloping surround sound. It also features advanced video processing capabilities, allowing users to upscale standard-definition and high-definition content to near 4K quality, further enhancing picture clarity.

In terms of user interface, the AVR600 provides an intuitive on-screen display and a well-designed remote control that makes navigating through settings and options seamless. The receiver is also compatible with smartphone apps for additional convenience, allowing users to control playback and settings directly from their mobile devices.

Overall, the Arcam AVR600 is a versatile audio-visual receiver that combines power, connectivity, and advanced technologies to create an exceptional home entertainment experience. Its unique blend of performance and flexibility makes it an excellent choice for those looking to invest in high-quality audio and video solutions for their homes.
Top Page Image Contents