Rear Panel Features | Genz-Benz NEOX400-210T guide

LED will illuminate for approximately 3 seconds during power switch-on and switch-off. It is normal for this LED to glow while continuing to monitor the internal conditions for about 3 seconds after the protection relay has closed. It will also illuminate during any internal fault condition. If this happens, turn the amp off and consult a repair technician.

∙The “thermal LED” indicates that the amplifier has overheated, engaged the protection circuit and shut down. This circuit is self-resetting when the offending condition (blocked air vents, foreign body stuck in fan, etc) is corrected. This LED will also flash for a brief time at turn-on and turn-off, indicating that the amplifier protection circuits are operating. An additional feature of this LED is that it will illuminate about 15 degrees F. before amplifier thermal shut-down, as a reminder that the operating conditions are too hot.

∙The “signal LED” indicates that the power amplifier is receiving signal (over several watts output) and all

is well!

∙The “limit LED” indicates that the power amplifier has reached maximum power and the limiter threshold has been crossed. Driving 6dB beyond this point, the amplifier will gradually begin to clip.

∙The “output limit switch” engages or bypasses the internal soft clip limiter. This limiter allows simulation of output saturation as the amplifier nears its maximum power. The limiting action is particularly musical sounding, even when driven hard.

REAR PANEL

FEATURES

Direct Output — This is a studio quality, fully active transformerless balanced “direct output”, with “pre-post equalization switch”.

With the “pre/post switch” in the “pre” position, the direct output receives its signal directly from the pre-amp input buffer amplifier with no tonal modifications. This is a pre gain control, pre eq output, with the best signal to noise ratio. Most recording and sound reinforcement companies will want to use this position since changes you make to your stage sound will not affect this output.

With the “pre/post switch” in the “post” position, the direct output receives its signal from the output of the 5 band equalizer. This feature allows for additional flexibility in some situations, but is often not desired for recording or live sound reinforcement.

A “ground lift switch” is provided which opens pin 1 (shield) on the direct output to prevent ground loops. Use the position that results in a minimum of noise.

The output level is nominal line level (adjustable to –30 or 0 dB), pin 2 hot. This output is fully protected from the effects of phantom power provided by the mixing console and does not require phantom power to operate.

Effects Insert Jacks — The “effects insert jacks” are provided to allow access to the pre-equalization signal for the purpose of inserting signal processing equipment such as compressors, chorus, delay & reverb processors. “Send” (output) and “return” (input) are nominal +4 dB level. “Series” devices (such as compressors and gates) require that the signal flow out from the send jack on the amplifier, through the processing device and back into the return jack on the amplifier. Parallel or mixed signal devices (such as

NEOX400-210T specifications

The Genz-Benz NEOX400-210T is a powerful bass amplifier developed for both professional and amateur musicians, particularly bass guitarists. Known for its reliability, impressive sound quality, and innovative features, the NEOX400-210T has established itself as a go-to choice for many players in various musical settings.

One of the standout features of the NEOX400-210T is its lightweight design. Utilizing advanced materials and construction techniques, the amplifier weighs significantly less than traditional models without sacrificing power or performance. This portability makes it easy for musicians to transport their gear to gigs or practice sessions, ensuring that the sound you desire is always within reach.

The amplifier boasts an impressive power output of 400 watts at 4 ohms, delivering a robust and clear sound that resonates well in live performances and studio recordings. The incorporation of dual 10-inch speakers provides an articulate low-end response, allowing bassists to achieve a rich, full sound that cuts through the mix. These speakers are housed in a specially-ported cabinet design that enhances bass response while minimizing unwanted resonance.

Another essential characteristic of the NEOX400-210T is its comprehensive EQ section. It features a 4-band EQ with adjustable controls for bass, midrange, and treble frequencies, enabling players to tailor their tone precisely to their liking. The presence of a parametric midrange control offers even greater flexibility, allowing users to pinpoint specific frequencies that best suit their instrument and playing style.

The NEOX400-210T also includes advanced technologies such as the unique Genz-Benz “Neo” speaker design, which utilizes neodymium magnets. These magnets provide a higher power-to-weight ratio, contributing to the overall efficiency and sound clarity of the amplifier. Additionally, the amplifier's construction features high-quality components that ensure durability and longevity, making it a solid investment for any bassist.

In summary, the Genz-Benz NEOX400-210T stands out in the world of bass amplifiers due to its lightweight design, substantial power output, flexible EQ options, and high-quality construction. With its combination of portability and professional-grade sound, it is an exceptional choice for players looking to elevate their performance whether on stage or in the studio. Whether you are a seasoned professional or an aspiring musician, the NEOX400-210T delivers the versatility and power needed to express your musical ideas effectively.