Sony CCD-TRV112, CCD-TRV33, CCD-TRV212 operating instructions Tips for using the battery pack

Page 35

Tips for using the battery pack

When to replace the battery

While you are using your camcorder, the remaining battery indicator in the viewfinder or on the LCD screen decreases gradually as battery power is used up.

When the remaining battery indicator reaches the lowest point, the i indicator appears and starts flashing in the viewfinder or on the LCD screen.

When the i indicator in the viewfinder or on the LCD screen changes from slow flashing to rapid flashing while you are recording, set the POWER switch to OFF on the camcorder and replace the battery pack. Leave the tape in the camcorder to obtain smooth transition between scenes after the battery pack has been replaced.

Note on the remaining battery indicator

The remaining battery indicator of the camcorder may indicate a different remaining capacity from that of the battery pack with its own indicator (not supplied). The indicator on the battery pack is more accurate.

Notes on the rechargeable battery pack

CAUTION

Never leave the battery pack in temperatures above 140°F (60°C), such as in a car parked in the sun or under direct sunlight.

The battery heats up

During charging or recording, the battery pack heats up. This is caused by energy that has been generated and a chemical change that has occurred inside the battery pack. This is not cause for concern and is normal.

Battery pack care

•Remove the battery pack from the camcorder after using it, and keep it in a cool place. When the battery pack is installed to the camcorder, a small amount of current flows to the camcorder even if the POWER switch is set to OFF. This shortens battery life.

•The battery pack is always discharging even when it is not in use after charging. Therefore, you should charge the battery right before using the camcorder.

How to use the switch on the battery pack

When the switch is supplied with the battery pack ([a] on page 36), you can use it to find whether the battery pack is charged or not. Set the switch to the “no mark” position when charging is completed. Set the switch to the “red mark” position when the battery is used up (or in whichever direction you want to remind yourself).

The life of the battery pack

If the battery indicator flashes rapidly just after turning on the camcordrer with a fully charged battery pack, the battery pack should be replaced with a new fully charged one.

Charging temperature

You should charge batteries at temperatures from 50°F to 86°F (from 10°C to 30°C). Lower temperatures require a longer charging time.

Sony Batteries are Recommended

Use of non-Sony batteries may damage your Handycam camcorder.

Additional information

35

CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Video Camera Recorder For the Customers in Canada WelcomeFor the Customers in the U.S.A Table of contents Types of differences Using this manualPrecaution on copyright Precautions on camcorder careChecking supplied accessories Charging Time Charging and installing the battery packCharging the battery pack Battery lifeInstalling the battery pack To remove the battery packTo eject the cassette Charging and installing the battery packTo remove the battery pack Inserting a cassetteTo finish recording b Camera recordingTo stop recording momentarily a Shooting scenery in several short takes Camera recordingTo focus the viewfinder lens Recording with the START/STOP button depressedCounter Reset Using the zoom featureShooting with the LCD screen When you shoot a subject using a telephoto zoomZooming speed Variable speed zooming To let the subject monitor the shot Hints for better shootingPlace the camcorder on a flat surface or use a tripod Hints for better shootingTo begin re-recording Checking the recorded pictureTo stop playback To go back to the last recorded point after edit searchPlayer Playing back a tapeVarious playback modes When watching on the LCD screenSearching for the end of the picture Using the house current Using alternative power sourcesCCD-TRV12/TRV22/TRV33 only Using alternative power sourcesUsing the Battery Case To remove the adaptorLetting the subject monitor the shot Using a car batteryTo cancel mirror mode To remove the battery caseTo stop recording with the date or time Recording with the date or timeLetting the subject monitor the shot This function is also effective under following conditions Shooting with backlightingAfter shooting To return to automatic mode Using the Program AE functionSelecting the best mode Using the Program AE functionTo extend the recording time in 5 SEC mode Selecting the START/STOP modeTo superimpose on the way of recording Superimposing a titleTo superimpose from the beginning CCD-TRV33 only Using the Steady Shot functionUsing the Cinema mode function CCD-TRV22/TRV33/TRV212 onlySelecting the mode setting of each item Changing the mode settingsTo connect to a VCR or TV without Video/Audio input jacks Watching on a TV screenIf your TV is already connected to a VCR If you connect directly to TVTo edit more scenes Editing onto another tapeTo stop editing Changing the lithium battery in the camcorder Changing the lithium battery Changing the lithium battery in the camcorderTo check the date and time Resetting the date and timeTo correct the date and time setting Year indicator changes as followsPlayback modes Tips for using the battery packBattery life is shorter in cold environment To save battery powerTips for using the battery pack Be Sure to Observe the Following Brand-new batteryAfter long storage If battery leakage occurred Maintenance information and precautions To reattach the eyecup Removing dust from inside the viewfinderCamcorder care Maintenance information and precautionsPrecautions Camcorder operation On handling tapesOthers AC power adaptorCharging Difference in color systems Using your camcorder abroadPower sources Camcorder Symptom Cause and/or Corrective ActionsTrouble check Trouble check SymptomWhen the Charge lamp does not flash again When the Charge lamp flashesWhen the Charge lamp flashes again Video camera recorder SpecificationsGeneral Power requirements AC power adaptorEditsearch button p Recording lamp Remote sensor p Lens cover Power zoom button pIdentifying the parts Tape transport buttons p , 17 p Stop@ Lanc l control jack Steady SHOT/CINEMA Mode switch p CCD-TRV33 onlyIdentifying the parts #Á START/STOP button p $» Jack cover Attaching the shoulder strap Transmitter Remote commander Using the Remote CommanderTo avoid damage from possible battery leakage To prepare the remote commanderTo watch the demonstration Remote control directionTo enter demo mode To exit demo modeViewfinder and on the LCD screen Lithium battery is weak or is not installed p Battery is weak or deadY, Z IndexK, L O, P
Top Page Image Contents