CONNECTION/INSTALLATION
Back focus adjustment
Be sure to make
●To make accurate back focus adjustments, carry out adjustments in a state where the lens iris is released.
To open the lens iris, set MODE in the FOCUS ADJUST menu screen to ON. ( Page 27)
●The auto iris lens may operate under extremely bright conditions (7000lx or higher). In this case, use an ND filter to adjust the amount of light.
(The ND fiter acts to reduce the amount of incident light entering the lens evenly over the entire wavelength band.)
Lens focus ring
Back focus adjust ring
Phillips screwdriver
Back focus locking screws
Memo
If the iris cable length of the lens is insufficient when turning the back focus adjustment rings, lock the back focus locking screws, turn the lens and loosen the back focus locking screws again for achieving back focus.
22
• With a fixed-focus lens
If the focus can not be adjusted correctly by rotating the lens focus ring, adjust the back focus as follows.
1. Loosen the back focus locking screws by turning it counterclock- wise (
) with a Phillips screwdriver. (2 locations)
2. Shoot a pattern closely.
3. Turn the lens focus ring to ∞.
4. Turn the back focus adjustment ring to focus at the best point.
5. Tighten the back focus locking screws by turning it clockwise (
). (2 locations)
• With a zoom lens
If the image is out of focus when zooming (telephoto
1. Loosen the back focus locking screws by turning it counterclock- wise (
) with a Phillips screwdriver. (2 locations)
2.
3. Set the lens to the maximum telephoto position, and adjust the lens focus.
4. Set the lens to the maximum
(Repeat steps 3. and 4. two or three times.)
5. Tighten the back focus locking screws by turning it clockwise (
). (2 locations)
23
MENU SETTING
Menu settings
SEE INST- | DC12V |
|
|
RUCTION | AC24V | 1 | 2 |
MANUAL |
|
|
|
CLASS 2 ONLY (U TYPE) |
|
| |
ISOLATED POWER ONLY |
|
| |
| (E TYPE) |
|
|
SET SELECTOR
POWER VIDEO OUT
LL | INT |
SET button
SELECTOR button
— — — V I D E O A D J U ST — — —
| O |
|
| ||
| WD R M D E |
| MO D E 2 | ||
| A G C M OD E |
| L OW | ||
| WH I T E B A L A | N C E | A T W | ||
| C O L O R L E V E L | N O R MA L | |||
| E N HA NC E L E V E L | N O R MA L | |||
| E X I T |
|
| ||
|
|
|
| ||
|
| ||||
| — — — V I D E O A D J U ST — — — | ||||
| O | MO D E 2 | |||
| WD R M D E | ||||
| A G C M OD E |
| H I GH |
| |
| WH I T E B A L A N C E | A T W |
| ||
| C O L O R L E V E L | N O R MA L | |||
| E N HA NC E L E V E L | N O R MA L | |||
| E X I T |
|
| ||
|
| ||||
|
| ||||
| — — — V I D E O A D J U ST — — — | ||||
4.Press the SELECTOR button in the vertical direction (6 or 7) and move the cursor (>) to the desired item.
5.Press the SELECTOR button in the
horizontal directional (8 or t) and change the set value.
To change the set value of multiple items, repeat steps 4. and 5. above.
6. | Exit the menu screen. |
| Move the cursor (>) to EXIT of the |
| menu screen and press the SET |
| button. |
7. | Return to the normal screen. |
Cursor
— — — ME N U — — —
F OCU S A D J U S T . .
V I D E O A D J U S T . .
C AM E R A S E T T I N G S . .
F A C T O R Y S E T T I N G S . .
E X I T
Submenu (“..” displayed at the end.)
— — — V I D E O A D J U ST — — —
Operation
1. | Press and hold the SET button for |
| more than 2 seconds. |
| ● The MENU screen appears. |
2. | Press the SELECTOR button in |
| the vertical direction (6 or 7) and |
| move the cursor (>) to the desired |
| submenu. |
3. | Press the SET button |
| ● The selected submenu screen |
| appears. |
WD R M OD E | MO D E 2 | |
A G C M OD E | H I GH | |
WH I T E B A L A N C E | A T W | |
C O L O R L E V E L | N O R MA L | |
E N HA NC E L E V E L | N O R MA L | |
E X I T |
|
|
— — — ME N U — — —
F OC U S A D J U S T . .
VI D E O A D J U S T . . CAME R A S E T T I N G S . . F A C T O R Y S E T T I N GS . .
E X I T
Move the cursor (>) to EXIT of the |
MENU screen and press the SET |
button. |
● The screen returns to the normal |
screen (screen with no menu dis- |
play). |
WD R M OD E | MO D E 2 |
A G C M OD E | L OW |
WH I T E B A L A N C E | A T W |
C O L O R L E V E L | N O R MA L |
E N HA NC E L E V E L | N O R MA L |
E X I T |
|
Memo
When returning to the normal screen from the TOP MENU screen by selecting EXIT, the menu settings will be stored in the unit memory.
24 | 25 |