Connecting Mounting, Setup | JVC TK-C210FW manual

Installation and connection (continued)

4. Remove the outer case.

Connecting

Mounting

Mounting the Camera to the Ceiling (continued)

Embedding the camera to the ceiling

*Make use of a ceiling material with a thickness between 9.5 mm to 22 mm.

Setup

1. Open a hole in the ceiling. (R120 mm)

2. Draw the fall prevention wire mounted to

the ceiling slab and the cable out from the

ceiling in advance.

CAUTION:

● Select a suitable safety cable based on

length, strength, location, material

(insulation property), etc.

● Use a ring on the fall prevention wire for

mounting to the camera unit with an

(This method does not require an outer case.)

A Loosen the outer case fastening screw with a screwdriver

B To remove, turn the camera unit in the anti- clockwise direction

5.Dismantle the supplied fall prevention wire

Unfasten the mounting screw for the fall prevention wire at the rear of the camera unit

6.Loosen the pan fastening screw.

CAUTION:

Moving the lens unit without loosening the pan fastening screw may damage the lens unit.

7.Set the switches for video images.

(TK-C215V4 A pg. 10) (TK-C215V12 A pg. 12) (TK-C210FW A pg. 14)

1.Attach the fall prevention wire to the camera, followed by attaching it to the ceiling slab (Fall prevention wire is not included.)

2.Connect the video signal cable. (A pg. 14)

Lower the cover and connect the connectors. Upon connecting, cover the connectors using the protection cover.

3.Connect the input power supply cable. (A pg. 15)

4.Install the Ferrite core (TK-C210FW only) (A pg. 14)

5.Connect the alarm cable. (TK-C215V12 only) (A pg. 15)

6.Wrap insulation tape around cables.

7.Insert the camera unit into the ceiling hole.

1.Align j with the shooting direction when mounting the camera.

2.Fasten the camera. (x3 locations)

A Press the screw head of the clamping bracket all the way in using a cross screwdriver.

B With the screw pressed in using the screwdriver, turn about 90 in the clockwise direction, followed by pulling out the screwdriver.

CThe clamping bracket is attached to the ceiling and the camera fastened.

NOTE:

Dismantle the camera upon turning the screw heads of the ceiling mount bracket (x3) by 90 in the anti-clockwise direction.

internal diameter of at least R3.1 mm or and

not larger than R5.5 mm, and an external

diameter that is not larger than R9 mm.

	4.	Pan fastening
	A	Screw
7.	A
7.

Alarm signal cable (TK-C215V12 only)

3.5.

R120 mm

Fall preven-	2.
tion wire
(not supplied)

Solder or crimp

Fall prevention	Approx. 100 mm
wire
(not supplied)	2.

Video signal cable	Camera
	Fastening Screw
Alarm signal cable	Power supply cable

Protection cover

Insulation tape

Wrap with tape

Input power supply cable

T	UP
	FRON

*TK-C215V12 only

3. Remove the dome cover.

As illustrated in the diagram, hold the dome

4. B	5.
	5.
	Washer

Align with shooting direction	2.	A

*TK-C215V4 is used in the above illustration

ring such that the position mark comes

between the thumb and index finger. Turn the

ring in the anti-clockwise direction to remove.

*TK-C215V4 is used in the above illustration

*TK-C215V12 is used in the above illustration

Adjusting Images

After mounting is completed, adjust the images while checking the actual image.

(A pg. 23 AAdjusting ImagesB)

Dome Ring Position mark