JVC LYT0002-0L5A, GR-AXM88UM manual Dc Out, AA-V11EG

Page 9

EN 9

 

**CHARGE MARKER

Charge marker

A charge marker is provided on the battery pack to

help you remember whether it has been charged or

 

 

not. Two colors are provided (red and black)—you

 

choose which one means charged and which

 

means discharged.

NOTES:

The recording time per charge is affected by such factors as the time spent in Record/Standby mode and the frequency of zooming. It is safer to have spare battery packs.

Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully charged battery pack.

Charging and discharging times vary according to the ambient temperature and the status of the battery pack.

Remember to set the charge marker after charging a battery pack or after detaching a discharged one from your camcorder.

Perform the REFRESH function after no less than 5 chargings.

High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t allow it to discharge in container, such as a bag.

If you stop recharging or discharging part way through, make sure to remove the battery pack before unplugging the adapter’s AC cord.

Remove the battery pack from the adapter immediately after discharging.

To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

Make sure you unplug the DC cord before charging or discharging the battery pack.

A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to continue.

The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG. indicator should light during recharging. If not, contact your nearest JVC dealer.

DC OUT

To AC outlet

 

terminal

 

To DC

 

 

in jack

 

 

 

AC Power

 

Adapter/Charger

DC cord

AA-V11EG

 

 

 

 

To car's

 

 

cigarette

Car Battery Cord

 

lighter socket

 

 

AP-V7U (optional)

 

 

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery Charger/Adapter (connect as shown in the illustration to the left).

NOTES:

When using the car battery, leave the engine idling.

The optional Car Battery Charger (BH-V3U) can also be used to charge the battery pack.

When using the optional Car Battery Charger or Car Battery Cord (AP-V7U), refer to the respective instruction booklet.

USING AC POWER

Use the AC Power Adapter (connect as shown in the illustration to the left).

NOTE:

The supplied AC Power Adapter/Charger features automatic voltage selection in the AC range from

Car Battery Charger/Adapter 110 V to 240 V.

BH-V3U (optional)

Image 9
Contents GR-AXM88UM This unit is produced to comply with Standard IEC Publ Dear CustomerInstallation Antenna Installation InstructionsRequirements for the grounding electrode USE ServicingTo avoid personal injury Eject Push Monitor Open BATT. ReleasePLAY/PAUSE Stop REWCassette Adapter Battery Pack Zoom-in Zoom-outCharger AA-V11EG VHS PlayPak C-P7U BN-V11U Contents Supply Power PowerAttach Battery Pack Detach Battery PackAA-V11EG DC OUTViewfinder Adjustment Start Clock Operation Close MenuNear Menu FAR SET Recording Mode Recording Mode SettingSet Power to Camera Tape length indicator Recording mode indicatorLoading/Unloading a Cassette EN Getting S Tarted Grip AdjustmentShoulder Strap Attachment Tripod MountingLoad a Cassette Enter RECORD-STANDBY ModeStart Shooting Stop RecordingBefore the following steps, perform pg Start/Stop Power indicatorJournalistic shooting Self-recordingBrightness control EN Recording FeatureRetake R/F PurposeSET Video Light Video LightLight OFF/AUTO/ON JVC dealer for replacing the video lightAfter 1 sec Program AE With Special EffectsMark Program AE select dialAuto Mode Lock Symbol Viewfinder indicationAuto Mode Release DialEN Recordi NG FocusingLock Focus Release Focus LockFAR Near Power zoom lever Program AE select dialExposure Control Picture StabilizerTo Cancel FADE- or Wipe Standby Mode Engage FADE- or Wipe Standby ModeFade/Wipe Select FunctionRestore Normal Screen Engage Wide ModeSelect Preset Title Instant TitlesMenu button Date/Time Character Insert Choose Display ModeSelect Display SET SELAdjust Focus Manual White Balance Adjustment M.W.BAdjust White Balance Select White BalanceMake Setting Access Menu ScreenDetailed camcorder settings MenuNorm OFFJlip ID no EN Recordi NG Time-Lapse AnimationSpeaker volume control EN PlaybackRewind or Fast-forward the tape Operation FF Stop REW PLAY/PAUSE Counter R/M FeatureConnection To a VCR a EN Playback Basic Conn ectionsEditing, Dubbing and Playback Connect Camcorder to TVInsert Cassette in Adapter Cassette Adapter VHS PlayPakPlay Back on Connected VCR Remove Cassette from AdapterVCR Recording deck SET Remote to Operate VCR Random Assemble Editing R.A.EditOperate the VCR Connect toDitin G END Automatic Editing Begin Automatic EditingEdited Tape VCR Stop EditInstalling The Battery EN Using R Emote Control UnitPull OUT Battery Holder Replace Battery HolderRec Time Indicator LCD monitor or viewfinder Index Code Marking Interval Timer IndicatorViss RM-V700UInsert editing Indicator Counter R/M PowerTape Counter Recorded tape, and press Pause at exactly atTo MIC Audio dubbing indicatorCapped REW DUBSet to Power OFF BATT. Release Push EjectRemove Symptom Tape won’t eject An error number i.e. E03 appearsShooting a very bright object Rear of the LCD monitor is hotFocus Indicator Displayed. When the Power switch is set toTape Time Tape End Display Tape END ........... pg50EN Counter R Reset/M Memory Power Switch Pg.15 Recording Mode SP/EP SelectTally Lamp Power On Indicator Multi-Function ControlDate/Time Setting Auto Mode Lock ModeDiopter Adjust Grip AdjustmentTo prevent damage and prolong service life Using Household AC Plug AdapterPlug adapter To avoid hazardAvoid using the unit For safety, do notTo prolong service life During useSize Out connectorLCD system LCD/TFT active matrix System Output Vp-p, 75 ohmsGR-AXM88UM