JVC GR-DVF25 manual Power lamp blinks There are disturbances in audio, Recommended to charge it

Page 62

62EN

TROUBLESHOOTING(cont.)

SYMPTOM

37.The charge indicator on the AC Power Adapter/ Charger does not light.

38.The recording mode indicator “LP” blinks.

39.Picture does not appear on the LCD monitor.

40.Picture does not appear in the viewfinder.

41.When the image is printed from the printer, a black bar appears at the bottom of the screen.

42.The power lamp blinks.

43.There are disturbances in audio.

POSSIBLE CAUSES

 

CORRECTIVE ACTION

37. •The temperature of the

 

37. • To protect the battery, it is

battery is extremely high/low.

 

recommended to charge it in

•Charging is difficult in places

 

places with a temperature of

subject to extremely high/low

 

10°C to 35°C (pg. 69).

temperatures.

 

 

 

 

 

38. •This occurs when recording

 

38.

in the LP mode is not

 

 

available. After the indicator

 

————

blinks, the recording mode

 

 

 

switches to “SP” and

 

 

recording goes on.

 

 

 

 

 

39. •The lens cover is closed.

 

39. • Open the lens cover

•The LCD monitor is not open

 

(pg. 14).

at an angle of over 60

 

• Open the LCD monitor to an

degrees.

 

angle of over 60 degrees.

•The LCD monitor’s brightness

 

• Adjust the brightness of the

setting is too dark.

 

LCD monitor (pg. 17).

 

 

• If the monitor is tilted

 

 

upward to 180 degrees,

 

 

open the monitor fully

 

 

(pg. 17).

 

 

 

40. •The lens cover is closed.

 

40. • Open the lens cover

•The LCD monitor is open.

 

(pg. 14).

•If the LCD monitor is not

 

• Close the LCD monitor.

facing forward towards the

 

• Open the LCD monitor and

subject, Interface Shooting

 

tilt it upward 180 degrees so

will not be possible.

 

that it faces forward

 

 

(pg. 17).

 

 

 

41. •This is not a malfunction.

 

41. • By recording with Picture

 

 

Stabilizer activated

 

 

(pg. 18) this can be

 

 

avoided.

 

 

 

42. •The camcorder was turned

 

42. • Replace with a charged

on when the battery power

 

battery pack (pg. 6)

was almost gone.

 

 

 

 

 

43. •If Audio Dubbing has

 

43. • Use a new, or infrequently

been performed

 

used, tape for Audio

repeatedly on the same

 

Dubbing (pg. 56, 57).

portion of the tape,

 

 

disturbance to the sound

 

 

may result.

 

 

 

 

 

Image 62
Contents GR-DVF25 This unit is produced to comply with Standard IEC Publ Dear CustomerIt is recommended that you About Batteries About DV Contents Using the Battery Pack PowerCharging the Battery Pack Charge Marker Using AC PowerUsing a CAR Battery Choose which one means charged and which means dischargedRemove Battery Holder Pull out the battery holder Clock Lithium Battery Insertion/RemovalInsert Battery in Holder RE-INSERT HolderAccess DATE/TIME Menu Date/Time SettingsSelect Operation Mode Access Recording MenuOpen Cassette Cover ContOpen LCD Monitor INSERT/REMOVE TapeFirst move the highlight bar to REC Mode by Recording Mode SettingSET Recording Mode Set depending on your preferenceGrip Adjustment Viewfinder AdjustmentTripod Mounting Adjust LengthShoulder Strap Attachment Attach StrapPRO. mode Power Switch PositionFull Auto mode Load a CassetteRecording Stop RecordingPress Display Button Indicaitons reappearBefore the following steps, perform pg Recording Basic RecordingShooting While Watching The LCD Monitor Brightness Control Journalistic ShootingInterface Shooting Zoom Feature Picture StabilizerBasic Recording Zoom OutFeature Video Light To brighten the scene when natural lighting is too dimWhen blank portion is recorded on a tape Proper recordingSelect Function Recording Advanced Features EN21Displaying The Date And Time During Recording SET Function ParametersSnapshot Advanced FeaturesSnapshot Mode Selection Snapshot RecordingMotor Drive Mode EN23END Setting Using Menu For Detailed AdjustmentMake Setting Select Function Parameters in DATE/TIME Menu or System MenuFactory-preset Recording Menu ExplanationsDate/Time Menu Explanations System Menu ExplanationsFADE/WIPE Selection Fade/Wipe EffectsEffect Selection B K , , B WBefore the following steps, perform steps 1 through 3 on pg Store Scene in Memory Engage the Record-Standby modePicture Wipe or Dissolve Selection P, P, P, P , P, P and P If you select Picture Wipe/Dissolve during recordingFader And Wipe Menu MenuDisable Mode Recording Advanced FeaturesSelect Mode Programme AE With Special EffectsSepia ShutterTwilight MonotonePatterns that are regularly repeated FocusingAuto Focus Adjust Focus Access Manual Mode Item MenuAccess Manual Focus END Adjustment of FocusExposure Control Access Exposure ControlIf you want to reset the exposure, repeat step To darken the imageIris Iris LockCentre SUBJECT, Lock Iris To Return To Automatic Iris ControlSelect Auto in . Or set the Power Switch to White Balance AdjustmentAccessment White Balance Adjust To Return To Automatic White BalanceExit Manual White Balance AD- Justment Enter SettingManual White Balance Operation To Change The Tint For RecordingRewind or Fast-forward the tape Speaker Volume ControlPlayback Basic Playback Feature Slow-Motion Playback Feature Still PlaybackFeature Shuttle Search Feature Playback ZoomEN Playback Playback MenuRecording sound Display Output sound Playback SoundDisplaying The Time Code During Playback Use the provided Audio/Video A/V cable and S-Video cable When connecting the cables, open this coverEN Playback Connections Use the provided Audio/Video A/V cableTurn on the camcorder, the VCR and the TV Connectinput VCR Output to TV Supply PowerConnectvcr Camcorder to TV or Tape Dubbing Remote control uses one lithium battery CR2025 Installing The BatteryPull OUT Battery Holder Functions ButtonsTo allow slow-speed search in either direction To stop Slow-Motion Playback in progess, press PlayEND Zoom Playback ZoomActivate Zoom DownStart Playback Accessmenu Playback Effect SelectPlayback Special Effects Select Playback EffectSET Remote to Operate VCR Random Assemble Editing R.A.EditSET REMOTE/VCR Code Operate VCRMake Connections Select ScenesUSE Programme AE with Special Effects if Necessary Select ScenesUSE FADE/WIPE on Scene Transition if Necessary Press FADE/WIPEStop Editing Automatic Editing to VCRPrepare Source Tape Prepare for R.A. Edit For More Accurate EditingDiagnosing VCR’S Against Camcorder Timing Choose a SceneInput Correction Data Adjustment of VCR’S Against Camcorder TimingAccess Playback Menu Close MenuPause During Dubbing Audio DubbingBegin Dubbing Stop DubbingOriginal and new tracks are combined and output in stereo New track is output on both L and R channels in stereoCorrective Action When using Picture Wipe Snapshot mode cannot be used Digital Zoom does not workShutter mode of Programme Delay of a fraction of aPicture Wipe function does not work Places subject to low Adjust the brightnessCamcorder When the LCD monitor’s Fluorescent light reaches Disappear Than 1 second to makeImages on the LCD monitor are jittery Battery pack, etc., clockRear of the LCD monitor is hot LCD monitor or viewfinder indications blinkRecommended to charge it Power lamp blinks There are disturbances in audioTemperature To protect the battery, it is Charging is difficult in placesClean Lens Clean ExteriorClean LCD Monitor After Use64EN Connectors to r are located beneath Video Light Switch$ Power Switch Battery Release Switch External Stereo Microphone Input Connector MICFunction IndicationsLCD Monitor/Viewfinder Indications During Recording 444Function LCD Monitor/Viewfinder Indications During PlaybackIndications Function Date/Time Display Pg , 7Pg , 42 Exposure Control ...................................... pgTo avoid hazard For safety, do notAvoid using the unit During useTo protect the unit, do not To prolong service lifeDo not leave the unit To prevent damage to the LCD monitor, do notCamcorder AC Power Adapter/Charger AA-V15EKConnectors GeneralGR-DVF25