JVC GR-DVL707 Grip Adjustment, Viewfinder Adjustment, Shoulder Strap Attachment, Tripod Mounting

Page 8

Separate the Velcro strip.

Pass your right hand through the loop and grasp the grip.

8 EN

Power

Zoom Lever

Recording

Start/Stop button

Power Switch

Dioptre Adjustment

Control

PAUSE

21

3

GETTING STARTED (cont.)

Grip Adjustment

1

2

3 Adjust so that your thumb and fingers can easily operate the Recording Start/Stop Button and Power Zoom Lever. Refasten the Velcro strip.

Viewfinder Adjustment

1 Set the Power Switch to “ ” or “ ” while pressing down the Lock Button located on the switch.

2 Turn the Dioptre Adjustment Control until the indications in the viewfinder are clearly focused.

Shoulder Strap Attachment

1 Make sure the battery pack or DC cord is removed. Following the illustration, thread the strap through the eyelet 1, then fold it back and thread it through the buckle 2. Repeat the procedure to attach the other end of the strap to the other eyelet 3 located under the Grip Strap, making sure the strap is not twisted.

Tripod Mounting

1 Align the screw and camera direction stud on the tripod with the camera’s mounting socket and stud hole. Then tighten the screw.

•Some tripods are not equipped with studs.

CAUTION:

When using a tripod, be sure to open and extend its legs fully to stabilise the camcorder. To prevent damage to the unit caused by falling over, do not use a small- sized tripod.

Image 8

Contents GR-DVL800 GR-DVL707 Dear Customer It is recommended that youEN3 Before recording an important sceneDC Cord AC Power Adapter Charger AA-V40ED Battery PackLens Cap Already attached to the camcorder Editing Cable Automatic Demonstration Power Charging the Battery PackLithium-ion is vulnerable in colder temperatures About BatteriesUsing the Battery Pack Using AC PowerTo Detach The Battery Pack Approximate recording timeGrip Adjustment Viewfinder AdjustmentShoulder Strap Attachment Tripod MountingDate/Time Settings Press MENU/BRIGHT. The Menu Screen appears10 EN Loading/Unloading a CassetteEN11 Recording Mode SettingSet the tape recording mode depending on your preference Picture Quality Mode Setting 12 ENOFF Operation ModeEN13 To Adjust The Brightness Of The Display 14 ENWhile recording is in progress To Stop RecordingSELF-RECORDING EN15Journalistic Shooting Power Switch Snapshot For Video Recording Snapshot Mode SelectionMotor Drive Mode 16 ENBasic Shooting Snapshot Available Snapshot modes are the same as those on pgImage is stored in the camcorder’s built-in memory To Delete Unwanted Still ImagesSlide the Power Zoom Lever towards T 18 ENZoom Zoom OutProper recording When a blank portion is recorded on a tapeEN19 Feature Video Light To brighten the scene when natural lighting is too dim20 EN Set Light OFF/AUTO/ON as requiredFeature Auto Focus Feature Manual FocusEN21 To obtain correct focusUsing Menus For Detailed Adjustment AppearsSee pg Go to stepMenu Screen Explanations EN23 Menu Screen Explanations EN25 Fade/Wipe Effects To Deactivate The Selected EffectSelect OFF in step If you select Picture Wipe/Dissolve during recordingEN27 Fader And Wipe MenuTo Deactivate The Selected Mode Programme AE With Special EffectsSlow Slow Shutter SlowEN29 Exposure ControlIris Lock White Balance Adjustment Manual White Balance OperationTo Return To Automatic White Balance To Change The Tint For RecordingTo Control The Speaker Volume Available only with the remote control provided pgEN31 Playback Zoom and Playback Special EffectsUsing Menus For Detailed Adjustment EN33 Playback SoundDisplay 34 EN Normal PlaybackEN35 Index ScreenIndex Playback After , press 4/6. To stop the Slide Show, press 36 ENSlide Show Protecting Images EN37To Protect AN Image To Remove Protection38 EN To Delete ALL ImagesYou can initialise the camcorder’s built-in memory anytime Initialising The Built-in MemoryEN39 40 EN Playback Basic ConnectionsIf using a VCR . . . go to step If not . . . go to step EN4142 EN Connection To a Personal ComputerMake sure all units are turned off Connection To a Video Unit Equipped With a DV ConnectorEN43 VCR Recording deck 44 ENDubbing To a VCR EN45 To use this camcorder as a playerMemory To a Tape Indicator disappears when dubbing is complete46 EN Dubbing Images Recorded On a Tape To The Built-in Memory EN47Installing The Batteries RM-V716U Installing The Battery RM-V711U, provided with GR-DVL80048 EN Provided with GR-DVL707EN49 Functions ButtonsFeature Slow-Motion Playback Feature Frame-By-Frame PlaybackFeature Playback Zoom 50 ENFeature Playback Special Effects EN51VCR Code List 52 ENRandom Assemble Editing R.A.Edit SET REMOTE/VCR CodeJVC VCR equipped with a remote pause connector EN53Make Connections VCR other than above54 EN Select ScenesEN55 Automatic Editing to VCR56 EN For More Accurate EditingDiagnosing VCR/CAMCORDER Timing Recording deckAdjustment of VCR/CAMCORDER Timing EN57Set 12BIT Mode to Sound 2 or MIX Menu Screen pg 58 ENAudio Dubbing To hear the dubbed sound during playbackDark place, or the contrast Focus again pg Was low Clean the lens and checkCorrective Action Troubleshooting 60 ENEN61 LCD monitor. When This happens, the displayed When the LCD monitors62 EN Angle of the LCD monitorEN63 Blink64 EN After Use Cleaning The Camcorder Press Battery Release and remove the battery packTurn off the camcorder Press Push Here to close the cassette holder66 EN 345 6 7 # $ %EN67 68 EN Appears when Digital Image Stabiliser DIS is engaged Automatically adjustedEN69 Approximate zoom ratio Appears during Zooming1Displays the sound mode LCD Monitor/Viewfinder Indications During Video PlaybackLCD Monitor/Viewfinder Indications During D.S.C. Playback 5Displays the time codeEN71 Indications FunctionDUB Error Check TAPE’S Erase Protection SwitchUnit in Safeguard Mode RemoveTo avoid hazards To prevent damage and prolong service lifeEN73 74 EN Serious malfunctioning EN75About moisture condensation 76 EN Date/Time Display pg , 32Icons pg LCD monitor/Viewfinder pg IndicationsEN77 Time Code pg , 25, 3278 EN For GeneralFor Digital Video Camera For Digital Still CameraFor Connectors EN790400MKV*UN*SN