JVC GR-DVM96 82 EN, Power, Video and D.S.C. Recording, Video/Memory, Set the VIDEO/MEMORY

Page 82

82 EN

TROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the beginning.

Power

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

1. No power is supplied.

1. •The power is not connected

1. •Connect the AC Adapter

 

properly.

securely. ( pg. 11)

 

•The battery is dead.

•Replace the dead battery

 

•The LCD monitor is not open

with a fully charged one.

 

fully or the viewfinder is not

( pg. 10, 11)

 

pulled out when recording.

•Open the LCD monitor fully

 

 

or pull out the viewfinder.

 

 

 

Video and D.S.C. Recording

SYMPTOM

 

POSSIBLE CAUSES

CORRECTIVE ACTION

2. Recording cannot be

2. •The Power Switch is set to

2. •Set the Power Switch to “A”

performed.

 

“P” or “OFF”.

or “M”. ( pg. 14)

 

 

— For Video Recording —

— For Video Recording —

 

 

•The tape’s erase protection

•Set the tape’s erase

 

 

tab is set to “SAVE”.

protection tab to “REC”.

 

 

•The VIDEO/MEMORY

( pg. 16)

 

 

Switch is set to “MEMORY”.

•Set the VIDEO/MEMORY

 

 

•“TAPE END” appears.

Switch to “VIDEO”.

 

 

•The cassette holder cover is

•Replace with new cassette.

 

 

open.

( pg. 16)

 

 

— For D.S.C. Recording —

•Close the cassette holder

 

 

•The VIDEO/MEMORY

cover.

 

 

Switch is set to “VIDEO”.

— For D.S.C. Recording —

 

 

 

•Set the VIDEO/MEMORY

 

 

 

Switch to “MEMORY”.

 

 

 

3. When shooting a subject

3. •This is a result of exceedingly

3.

illuminated by bright light,

 

high contrast, and is not a

—

vertical lines appear.

 

malfunction.

 

 

 

 

 

4. When the screen is under

4.

•This is not a malfunction.

4.

direct sunlight during shooting,

 

 

—

the screen becomes red or

 

 

 

 

 

black for an instant.

 

 

 

 

 

 

 

5. During recording, the date/

5.

•“DATE/TIME” is set to “OFF”.

5. •Set “DATE/TIME” to “ON”.

time does not appear.

 

 

( pg. 38, 49)

 

 

 

 

Page 81 Page 83
Image 82
Page 81 Page 83
Contents For Customer Use Model No Serial NoDear Customer It is recommended that you…Important Safty Instructions Before recording an important scene… RM-V717U Remote Control Unit CD-ROMCamcorder USB Cable Memory Card 8 MB Lens Cap Already insertedHow To Attach The Grip Belt How To Attach The Lens Cap Attach the lens cap with the cut downward During shootingSet the Power Switch to M while pressing down Automatic DemonstrationGetting Started Using The Battery Pack PowerCharging The Battery Pack 10 ENAbout Batteries Using AC PowerFor other notes,  pg Viewfinder Adjustment Grip Adjustment12 EN While using the viewfinder While using the LCD monitorTripod Mounting VIDEO/MEMORY Switch Position Operation ModePower Switch Position Full Auto Recording 14 ENDate/Time Settings Built-in Clock’s Rechargeable Lithium BatteryLoading a Cassette Unloading a Cassette Approximate recording time Tape Recording mode16 EN To protect valuable recordings…Make sure the camcorder’s power is off Open the card cover To protect valuable files available only for SD Memory Card…18 EN Video Recording & PlaybackNow calculating Basic RecordingTape Remaining Time Blinking Blinking BlinkingJournalistic Shooting 20 ENZooming Self-RecordingRecording From The Middle Of a Tape When a blank portion is recorded on a tapeTime Code Proper recordingStill Playback 22 ENNormal Playback Shuttle SearchBlank Search Slow-Motion Playback Playback Zoom Playback Special Effects24 EN Connections To a TV Or VCR pg 26 EN Recording & PlaybackBasic Shooting D.S.C. Snapshot To change the Image Size and/or Picture Quality,  pgAuto Playback Of Images 28 ENImage playback screen Playback Of Video Clips GR-DVM96 only Viewing File Information 30 ENIndex Playback Of Files For Index Playback of video clip files, performProtecting Files Protect mode helps prevent the accidental erasure of filesIf you want to select another type of file, go to step To protect the currently displayed file 32 ENTo Remove Protection To remove protection from the currently displayed fileTo delete the currently displayed file Deleting FilesTo delete all files stored in the memory card Making a New Folder 34 ENFolder and File names To Reset The Number Of Prints To Print By Selecting Still Images And Number Of Prints36 EN Initializing a Memory CardAdvanced Features 38 EN Menus without Sub MenusMenus with Sub Menus CAMERA, q MANUAL, s SYSTEM, n DISPLAY, o DSC, t VideoWipe Or Fader Effects VIDEO/MEMORY Switch40 EN Menu WheelFADER-BLACK OFFFADER-WHITE FADER-B.W42 EN White Balance Adjustment Exposure Control44 EN Recording modeSound mode Camera MenuSnapshot mode for video recording Gain upWide mode Maximum telephoto setting46 EN Flash brightness adjustment Snapshot flash modeWind cut 48 EN Tally lamp settingAutomatic demonstration mode System MenuClock adjustment Date and time display settingTime code setting Display MenuImage size 50 ENRecording media selection Playback sound Synchro adjustmentVideo Menu Dubbing from tape to memory cardDATE/TIME OFF Auto Melody Tally OFF Demo Mode52 EN DisplayPress Snapshot Motor Drive ModeNight-Alive To deactivate Night-Alive…Snapshot Flash 54 ENIf Auto C is selected Auto Focus Manual Focus56 EN When the background is overly dark or the subject is brightBefore starting, perform the procedures listed below To return to automatic exposure controlBacklight Compensation Iris LockTo return to automatic iris control 58 EN To return to automatic white balance…To cancel recording the sound effect midway Downloading sound data from Web SiteMail Clip Recording GR-DVM96 only 60 ENTo make video clips from real-time camera image Refer to Deleting Files  pgTo make video clips from recorded video footage 62 EN Dubbing To a VCRDubbing Dubbing To a Video Unit Equipped64 EN Equipped With a DV OUTSet Dubbing Still Images Recorded On a Tape To a Memory CardStill images can be dubbed from a tape to a memory card To on  pg Press 4/9 to startBeam Effective Area indoor use Installing The Batteries66 EN Buttons And FunctionsPause in Connector With the camcorder’s PowerSwitch set to a or M Switch set to P Functions68 EN Slow-Motion PlaybackSelect Menu appears Press EFFECT.To move the highlight 70 EN Audio DubbingAudio Dubbing Using Digital Sound Effects GR-DVM96 only SOUND, Press it Rotate the Menu72 EN Insert EditingSet Remote/VCR Code Random Assemble Editing R.A.EditYou are now ready to try Random Assemble Editing Make Connections A JVC VCR equipped with a Remote Pause connector…74 EN VCR other than above…Select Scenes If the search time for an in-point exceeds76 EN Automatic Editing To VCRFor More Accurate Editing Adjustment Of VCR/Camcorder TimingDiagnosing VCR/Camcorder Timing 78 EN Using USB cableUsing DV cable Connection To a Personal ComputerIf the PC is not Using The Camcorder As a WebCam GR-DVM96 onlyThis camcorder can be used as a WebCam via USB connection Disconnect the USB cable from the camcorder and PC80 EN ReferencesDetach the battery from the camcorder Power  pgSet the Power Switch to P, a or M When a cassette at its end is loadedVideo and D.S.C. Recording Power82 EN VIDEO/MEMORYViewfinder indications blink VIDEO/MEMORY Switch is Set the VIDEO/MEMORYSwitch is set to Video Switch to Memory 200X.  pg84 EN Advanced featuresPress Backlight Other problems 86 EN Camcorder When the LCD monitor’sAngle of the LCD monitor Cause damage.  pg Re-insert it, then check if88 EN General Battery PrecautionsBattery Packs CassettesLCD Monitor Memory CardsMain Unit About moisture condensation How To Handle a CD-ROM90 EN Serious malfunctioningTurn off the camcorder Cleaning The CamcorderAfter Use Press Push Here to close the cassette holder92 EN Audio output For Connectors Video outputFor General Power requirement A. and Canada Headphone output94 EN Controls ConnectorsIndicators Other PartsIndications Selected Wipe/Fader Effect Indicator96 EN Tape Remaining Time  pg REC Appears during recordingAppears and blinks during shooting Appears during shooting and blinks when aShooting Icon Card Icon98 EN ExplosionPause Forward Slow-Motion Reverse Slow-Motion Monitor  pg Level indicator g moves Time CodeAudio Dubbing 9D Audio Dubbing Pause 100 EN Unit in Safeguard Card ErrorSwitch Mode Remove102 EN Program AE With Special Effects Playback sound Sound ModeWide Mode Wide Mode Recording TimeGR-DVM96 GR-DVM76
Top Page Image Contents