JVC LYT0193-001B specifications Troubleshooting

Page 68

68EN

TROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.

SYMPTOM

1.No power is supplied.

2.“SET DATE/TIME!” appears.

3.Recording cannot be performed.

4.There is no playback picture.

5.Some functions are not available using the MENU button.

6.Some functions are not available using the Select Dial.

7.The focus does not adjust automatically.

8.The cassette won’t load properly.

9.Play, Rewind and Fast- Forward functions don’t work.

POSSIBLE CAUSES

1.•The power is not connected properly.

•The battery is dead.

•The viewfinder is not pulled out when recording.

2.•The built-in rechargeable clock lithum battery is discharged and the previ- ously set date/time is erased.

3.•The tape’s record safety tab is set to “SAVE”.

•The Power Dial is set to “PLAY”.

•“TAPE END” appears.

•The cassette's cover is open.

4.•The camcorder is not getting power, or some other malfunction exists.

5.•The Power Dial is set to “ A ”.

6.•The Power Dial is set to “ A ”, “5S” or “”.

7.•Focus is set to “MANUAL”. •The recording was done in a dark place, or the contrast

was low.

•The lens is dirty or covered with condensation.

8.•The cassette is in the wrong position.

•The battery’s charge is low.

9.•The Power Dial is not set to

“PLAY”.

CORRECTIVE ACTION

1.• Connect the AC Charger Station securely (☞ pg. 10).

•Replace the dead battery

with a fully charged one (☞ pg. 9).

•Pull out the viewfinder.

2.• Connect the camcorder to an AC outlet using the AC Charger Station etc. for over 24 hours to charge the

clock lithum battery (☞ pg. 11).

3.• Set the tape’s record safety tab to “REC” (☞ pg. 12).

•Set the Power Dial to “ A ”, “ M ”, “5S” or “”

(☞ pg. 17).

•Replace with new cassette (☞ pg. 12).

•Close the cassette's cover.

4.• Turn the camcorder’s power

off and on again (☞ pg. 18).

5.• Set the Power Dial to any

position except “ A ” (☞ pg. 17).

6.• Set the Power Dial to any

position except “ A ”, “5S” or “” (☞ pg. 17).

7.• Set Focus to “AUTO”

(☞ pg. 41).

•Clean the lens and check the focus again (☞ pg. 73).

8.• Set it in the right position

(☞ pg. 12).

•Install a fully charged battery (☞ pg. 9).

9.• Set the Power Dial to “PLAY” (☞ pg. 46).

Image 68

Contents GR-DV3 Connection to the mains supply in the United Kingdom Dear CustomerIt is recommended that you Some DO’S and DON’TS on the Safe USE of Equipment Safety Precautions ITI Insert and Tracking Information Area Sub-Code AreaVideo Area Audio Area Battery pack BN-V607U DC cordGrip/Hand strap VIDEO/AUDIO cableLithium battery CR2025 RM-V712U DVM-30 M-DV30ME Cable adapterCharging The Battery Pack Installing The Battery Pack Open Battery CoverInsert Charged Battery Close Battery CoverUsing The Battery Holder Supply Power to AC Charger StationIndoor Use Connect DC Cord to AC Charger StationDate/Time Settings Select Operation ModeInput Date and Time Select Dial Menu button DisplayLoading/Unloading a Cassette Open Cassette CoverINSERT/REMOVE Tape To protect valuable recordingsSelect Dial Recording Mode SettingSET Recording Mode Adjust Length Grip Strap AttachmentAttach Grip Strap to Hand Strap Eyelet Attach Grip Strap to SUB Hand Strap EyeletDioptre Adjustment Adjust DioptreTripod Mounting Turn on CamcorderRemote Control Unit Installing The BatteryPull OUT Battery Holder Insert Battery in HolderOperation Mode Power Dial PositionSelf-Timer Playback Play FunctionStart Recording Stop RecordingEND Recording Select Dial IND.ON/OFF buttonTape Remaining Indicator Adjust BrightnessBrightness Control Viewfinder IndicationsRecording From The Middle Of a Tape Proper recording When blank portion is recorded on a tapeTime Code EN Recording ZoomSelect Dial Menu button IND.ON/OFF button Displaying The Date And Time During RecordingSelect Function Engage 5S Mode Dissolves during 5 second mode recordingTo Take a Snapshot In The 5-Second Mode Scene 5-second recordingSelf-Timer Engage SELF-TIMER ModeStop SELF-TIMER Recording END SELF-TIMER RecordingAccess System Menu Select Snapshot ModeSnapshot Take SnapshotMotor Drive mode Recording Menu allows you to set these functions MenusClose Recording Menu REC Mode Recording mode Wide ModeZoom Zoom magnification DIS Digital Image StabilizerSystem Menu Close System MenuPhoto Mode Accessmenu Manual Mode Item Access FADER/WIPE MenuTo Cancel FADE/WIPE Effects FADE/WIPE EffectsFades and Wipes Example WH Fader WhiteExample Wipe Scroll WH , BK , , B WP and P of the Fader/Wipe Menu Picture Wipe/DissolveResume Recording Random Variations Fader and Wipe Menu Fader and Wipe Menu RandomDisable P.AE/EFFECT AE/EffectsSlow Slow Shutter Manual Focus Adjustment Access Manual FocusAdjust Focus To Change To Auto FocusAdjust Exposure Exposure ControlBrightness control of the display To Return To Automatic Exposure ControlIris Iris LockTo Return To Automatic Iris Control White Balance Adjustment Accessment White Balance AdjustClosement White Balance Adjust To Return To Automatic White BalanceEnter Setting Exit Manual White Balance AdjustmentManual White Balance Operation To Change The Tint For RecordingDisplay Rewind TapeViewing Recording END PlaybackStill Playback To Perform High-Speed SearchPlayback Zoom Activate ZoomLocatescene Portion of Magnified END ZoomAccessmenu Playback Effect Select Playback EffectsAccess Playback Menu Playback MenuClose Menu Playback Menu allows you to set the following functionsDisplaying The Time Code During Playback Playback SoundDisplaying the Date During Playback Select TV’S Video Mode VCR/TV Connection when connecting directly to the camcorderTurn on Power Attach and Lock VCR/TV Connection using AC Charger StationConfirm POWER-OFF Status VCR/TV connection using the AC Charger Station Only with regular video signalTo S-VIDEO OUT connector Digital Printer Connection To a Video Unit Equipped With a DV ConnectorTo DV in connector Supply Power Attach Camcorder to AC Charger StationDubbing Make Connections Start PlaybackPause Recording Recording deckDigital Dubbing Make ConnectionsBrand Setting Operate VCRRandom Assemble Editing Execute FADE/WIPE in if NecessaryPress FADE/WIPE USE Fade Wipe on Scene Transition if NecessaryUSE P.AE/EFFECT if Necessary Stop Editing Engagemode Vcrs RECORD-PAUSEStart Editing Choose a Scene For More Accurate EditingPrepare for R.A. Edit Play Back Dubbed Scene Input Correction Data Recording deck Select DialAudio Dubbing Find EDIT-IN Point Pause During DubbingStop Dubbing Engage Audio DUB StandbyRecording Sound Display Output Sound Troubleshooting Possible Causes Troubleshooting Phones connecto Viewfinder Camcorder’s functions Cleaning The Camcorder Remove Power SupplyClean Lens Clean ViewfinderCamcorder Power dial pg Zoom switch T/W pgOPEN/EJECT switch pg Bottom of camcorder Battery cover open switch Battery pgAC Charger Station Indications During Recording FunctionIndications During Playback Indications Function Store cassettes To avoid hazardDuring use For safety, do not Avoid using the unitDirty heads can cause the following problems Do not leave the unitAudio GeneralVideo Connectors Output powerVideo AudioColour temperature AC Charger StationAuto focus On-screen displayIndex Memo Memo GR-DV3