JVC LYT0583-001A specifications EN19, When a blank portion is recorded on a tape, Proper recording

Page 19

EN19

NOTE: Recording From The Middle Of A Tape

Time Code

During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded scene on the tape during playback.

If recording starts from a blank portion, the time code begins counting from “00:00:00” (minute:second:frame). If recording starts from the end of a previously recorded scene, the time code continues from the last time code number.

To perform Random Assemble Editing ( pg. 52 – 57), time code is necessary. If during recording a blank portion is left partway through the tape, the time code is interrupted. When recording is resumed, the time code starts counting up again from “00:00:00”. This means the camcorder may record the same time codes as those existing in a previously recorded scene. To prevent this, perform “Recording From The Middle of A Tape” below in the following cases;

•When shooting again after playing back a recorded tape.

•When power shuts off during shooting.

•When a tape is removed and re-inserted during shooting.

•When shooting using a partially recorded tape.

•When shooting on a blank portion located partway through the tape.

•When shooting again after shooting a scene then opening/closing the cassette holder cover.

Display

 

 

 

 

 

 

 

Frames are not displayed

 

 

 

 

 

 

 

during recording.

 

 

 

 

 

 

 

 

 

Minutes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Seconds

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Frames

TC 1

 

2 : 3

 

4 : 2

 

4

 

 

(25 frames = 1 second)

 

 

 

 

 

Recording From The Middle Of A Tape

1.Play back a tape to find the spot at which you want to start recording, then engage the Still Playback mode ( pg. 31).

2.Set the Power Switch to “ ” or “ ” while pressing down the Lock Button located on the switch, then start recording.

NOTES:

●The time code cannot be reset.

●During fast-forwarding and rewinding, the time code indication does not move smoothly.

●The time code is displayed only when “TIME CODE” is set to “ON” (  pg. 25, 32).

When a blank portion is recorded on a tape

Time code

Time code

Time code

00:00:00

05:43:21

00:00:00

Tape

Already recorded scene

Blank

Newly recorded scene

Shooting start pointShooting stop point Shooting start point

Proper recording

Time code

Time code

Time code

00:00:00

05:43:21

05:44:00

Tape

Already recorded scene

New scene

Latest scene

Shooting start point

Shooting start point

Shooting start point

Page 18 Page 20
Image 19
Page 18 Page 20
Contents GR-DVL200 It is recommended that you Dear CustomerAbove ALL EN3CD-ROM Release the stoppers on both ends of the Core Filter GR-DVL200EG Owners How To Attach The Core FilterAbout Batteries PowerCharging the Battery Pack Lithium-ion is vulnerable in colder temperaturesInformation Using the Battery PackUsing AC Power To Detach The Battery PackTripod Mounting Grip AdjustmentViewfinder Adjustment Shoulder Strap AttachmentPress MENU/BRIGHT. The Menu Screen appears Date/Time SettingsLoading/Unloading a Cassette 10 ENSet the tape recording mode depending on your preference Recording Mode SettingEN11 12 EN Picture Quality Mode SettingVideo Operation ModeEN13 OFFTo Stop Recording To Adjust The Brightness Of The Display14 EN While recording is in progressJournalistic Shooting EN15SELF-RECORDING 16 EN Power Switch Snapshot For Video RecordingSnapshot Mode Selection Motor Drive ModeTo Delete Unwanted Still Images Basic Shooting SnapshotAvailable Snapshot modes are the same as those on pg Image is stored in the camcorder’s built-in memoryZoom Out Slide the Power Zoom Lever towards T18 EN ZoomEN19 When a blank portion is recorded on a tapeProper recording Set Light OFF/AUTO/ON as required Feature Video LightTo brighten the scene when natural lighting is too dim 20 ENTo obtain correct focus Feature Auto FocusFeature Manual Focus EN21Go to step Using Menus For Detailed AdjustmentAppears See pgMenu Screen Explanations EN23 Menu Screen Explanations EN25 If you select Picture Wipe/Dissolve during recording Fade/Wipe EffectsTo Deactivate The Selected Effect Select OFF in stepFader And Wipe Menu EN27Programme AE With Special Effects To Deactivate The Selected ModeIris Lock Exposure ControlEN29 To Change The Tint For Recording White Balance AdjustmentManual White Balance Operation To Return To Automatic White BalancePlayback Zoom and Playback Special Effects To Control The Speaker VolumeAvailable only with the remote control provided  pg EN31Using Menus For Detailed Adjustment Display Playback SoundEN33 Normal Playback 34 ENIndex Playback Index ScreenEN35 Slide Show 36 ENAfter , press 4/6. To stop the Slide Show, press To Remove Protection Protecting ImagesEN37 To Protect AN ImageTo Delete ALL Images 38 ENEN39 Initialising The Built-in MemoryYou can initialise the camcorder’s built-in memory anytime 40 EN EN41 If using a VCR . . . go to step If not . . . go to stepConnection To a Personal Computer 42 ENEN43 Connection To a Video Unit Equipped With a DV ConnectorMake sure all units are turned off Dubbing To a VCR 44 ENVCR Recording deck EN45 46 EN Indicator disappears when dubbing is completeMemory To a Tape EN47 Dubbing Images Recorded On a Tape To The Built-in Memory48 EN Installing The BatteriesFF Button EN4950 EN Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback Feature Playback ZoomEN51 Feature Playback Special EffectsSET REMOTE/VCR Code VCR Code List52 EN Random Assemble Editing R.A.EditVCR other than above JVC VCR equipped with a remote pause connectorEN53 Make ConnectionsSelect Scenes 54 ENAutomatic Editing to VCR EN55Recording deck 56 ENFor More Accurate Editing Diagnosing VCR/CAMCORDER TimingEN57 Adjustment of VCR/CAMCORDER TimingTo hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen  pg58 EN Audio DubbingDark place, or the contrast Focus again  pg Was low Clean the lens and checkCorrective Action Bright60 EN TroubleshootingEN61 62 EN EN63 Or channel appropriate Video mode For video playbackBlink 64 EN Press Push Here to close the cassette holder After Use Cleaning The CamcorderPress Battery Release and remove the battery pack Turn off the camcorder345 6 7 # $ % 66 ENEN67 68 EN Approximate zoom ratio Appears during Zooming Appears when Digital Image Stabiliser DIS is engagedAutomatically adjusted EN695Displays the time code 1Displays the sound modeLCD Monitor/Viewfinder Indications During Video Playback LCD Monitor/Viewfinder Indications During D.S.C. PlaybackFunction EN71Mode Remove DUB ErrorCheck TAPE’S Erase Protection Switch Unit in SafeguardEN73 To prevent damage and prolong service lifeTo avoid hazards 74 EN About moisture condensation EN75Serious malfunctioning LCD monitor/Viewfinder  pg Indications 76 ENDate/Time Display  pg , 32 Icons  pgTime Code  pg , 25, 32 EN77For Digital Still Camera 78 ENFor General For Digital Video CameraEN79 For ConnectorsGR-DVL200

LYT0583-001A specifications

The JVC LYT0583-001A is a high-performance, versatile component designed for use in various professional video applications, particularly in the realm of broadcasting and videography. It is especially recognized for its notable capabilities in enhancing the image quality of camera systems while ensuring seamless connectivity across different media formats. One of the key features of the JVC LYT0583-001A is its advanced image sensor technology, which allows it to capture incredibly sharp and clear images even in low-light conditions. This sensor utilizes back-illuminated technology, maximizing light sensitivity and enhancing dynamic range, which is critical for professional videographers who often work in challenging lighting environments.

Additionally, the LYT0583-001A supports a wide range of resolutions and frame rates, including high definition and even 4K capabilities. This flexibility provides users with the tools they need to achieve high-quality results in both live productions and post-production processes. The device is also equipped with various output options, including HDMI and SDI, ensuring compatibility with numerous devices and systems within the broadcast industry.

In terms of usability, the LYT0583-001A features a user-friendly interface that allows for easy adjustments and settings modifications. The integration of advanced codec technology enables efficient compression and decompression of video files while maintaining top-notch quality, which significantly benefits storage and bandwidth management.

Moreover, the device’s built-in stabilization technologies offer smooth video capture, reducing the jarring effects often experienced in handheld shooting. This is especially beneficial for action shots or during dynamic camera movement, ensuring a professional finish to every project.

The JVC LYT0583-001A is also designed with durability in mind, making it suitable for various shooting conditions. Its robust construction and weather-resistant features allow it to perform reliably in outdoor environments, enhancing its usability for documentary filmmakers and event videographers.

In conclusion, the JVC LYT0583-001A stands out in the competitive landscape of professional video equipment, offering cutting-edge features and robust performance capabilities tailored to meet the demands of modern content creators. Its combination of advanced imaging technologies, reliable connectivity, and user-friendly operation makes it a worthy investment for any professional aiming to elevate their video production quality.
Top Page Image Contents