JVC LYT0583-001A specifications Corrective Action, Bright, Clean the lens and check

Page 59

TROUBLESHOOTING

EN59

If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power Adapter/Battery Charger, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the beginning.

 

SYMPTOM

 

 

POSSIBLE CAUSES

 

CORRECTIVE ACTION

1.

No power is supplied.

 

1. • The power is not connected

 

1. • Connect the AC Power

 

 

 

properly.

 

 

Adapter/Charger securely

 

 

 

• The battery is dead.

 

( pg. 7).

 

 

 

 

 

 

 

• Replace the dead battery

 

 

 

 

 

 

 

with a fully charged one

 

 

 

 

 

 

 

( pg. 6, 7).

 

 

 

 

 

 

2.

“SET DATE/TIME!”

 

2. • The date/time is not set.

 

2. • Set the date/time ( pg. 9).

 

appears.

 

• The built-in clock battery

 

• Consult your nearest JVC

 

 

 

has run out and the

 

dealer for replacement.

 

 

 

previously set date/time has

 

 

 

 

 

 

been erased.

 

 

 

 

 

 

 

 

 

3.

Recording cannot be

 

3. — For Video Recording —

 

3. • Set the tape’s erase

 

performed.

 

• The tape’s erase protection

 

protection tab to “REC”

 

 

 

tab is set to “SAVE”.

 

( pg. 10).

 

 

 

• The Power Switch is set to

 

• Set the Power Switch to

 

 

 

“

” or “OFF”.

 

“

” or “ ” ( pg. 13).

 

 

 

• The VIDEO/DSC Switch is

 

• Set the VIDEO/DSC Switch

 

 

 

set to “

”.

 

to “VIDEO”.

 

 

 

•“TAPE END” appears.

 

• Replace with new cassette

 

 

 

• The cassette holder cover is

 

( pg. 10).

 

 

 

open.

 

 

• Close the cassette holder

 

 

 

— For D.S.C. Recording —

 

cover.

 

 

 

• The VIDEO/DSC Switch is

 

• Set the VIDEO/DSC Switch

 

 

 

set to “VIDEO”.

 

to “

”.

 

 

 

• The camcorder’s built-in

 

•Delete unwanted still

 

 

 

memory is full.

 

images ( pg. 38).

 

 

 

 

 

 

4.

There is no picture.

 

4. • The camcorder is not getting

 

4. • Turn the camcorder’s power

 

 

 

power, or some other

 

off and on again ( pg. 13).

 

 

 

malfunction exists.

 

 

 

 

 

 

 

 

5. Some functions are not

 

5. • The Power Switch is set to

 

5. • Set the Power Switch to

 

available using MENU/

 

“

”.

 

 

“

” ( pg. 13).

 

BRIGHT.

 

 

 

 

 

 

 

 

 

 

 

 

6. The focus does not adjust

 

6. • Focus is set to the Manual

 

6. • Set Focus to the Auto mode

 

automatically.

 

mode.

 

 

( pg. 21).

 

 

 

• The recording was done in a

 

• Clean the lens and check

 

 

 

dark place, or the contrast

 

the focus again ( pg. 65).

 

 

 

was low.

 

 

 

 

•The lens is dirty or covered with condensation.

CONTINUED ON NEXT PAGE

Page 58 Page 60
Image 59
Page 58 Page 60
Contents GR-DVL200 It is recommended that you Dear CustomerAbove ALL EN3CD-ROM Release the stoppers on both ends of the Core Filter GR-DVL200EG Owners How To Attach The Core FilterAbout Batteries PowerCharging the Battery Pack Lithium-ion is vulnerable in colder temperaturesInformation Using the Battery PackUsing AC Power To Detach The Battery PackTripod Mounting Grip AdjustmentViewfinder Adjustment Shoulder Strap AttachmentPress MENU/BRIGHT. The Menu Screen appears Date/Time SettingsLoading/Unloading a Cassette 10 ENEN11 Recording Mode SettingSet the tape recording mode depending on your preference 12 EN Picture Quality Mode SettingVideo Operation ModeEN13 OFFTo Stop Recording To Adjust The Brightness Of The Display14 EN While recording is in progressSELF-RECORDING EN15Journalistic Shooting 16 EN Power Switch Snapshot For Video RecordingSnapshot Mode Selection Motor Drive ModeTo Delete Unwanted Still Images Basic Shooting SnapshotAvailable Snapshot modes are the same as those on pg Image is stored in the camcorder’s built-in memoryZoom Out Slide the Power Zoom Lever towards T18 EN ZoomProper recording When a blank portion is recorded on a tapeEN19 Set Light OFF/AUTO/ON as required Feature Video LightTo brighten the scene when natural lighting is too dim 20 ENTo obtain correct focus Feature Auto FocusFeature Manual Focus EN21Go to step Using Menus For Detailed AdjustmentAppears See pgMenu Screen Explanations EN23 Menu Screen Explanations EN25 If you select Picture Wipe/Dissolve during recording Fade/Wipe EffectsTo Deactivate The Selected Effect Select OFF in stepFader And Wipe Menu EN27Programme AE With Special Effects To Deactivate The Selected ModeEN29 Exposure ControlIris Lock To Change The Tint For Recording White Balance AdjustmentManual White Balance Operation To Return To Automatic White BalancePlayback Zoom and Playback Special Effects To Control The Speaker VolumeAvailable only with the remote control provided  pg EN31Using Menus For Detailed Adjustment EN33 Playback SoundDisplay Normal Playback 34 ENEN35 Index ScreenIndex Playback After , press 4/6. To stop the Slide Show, press 36 ENSlide Show To Remove Protection Protecting ImagesEN37 To Protect AN ImageTo Delete ALL Images 38 ENYou can initialise the camcorder’s built-in memory anytime Initialising The Built-in MemoryEN39 40 EN EN41 If using a VCR . . . go to step If not . . . go to stepConnection To a Personal Computer 42 ENMake sure all units are turned off Connection To a Video Unit Equipped With a DV ConnectorEN43 VCR Recording deck 44 ENDubbing To a VCR EN45 Memory To a Tape Indicator disappears when dubbing is complete46 EN EN47 Dubbing Images Recorded On a Tape To The Built-in Memory48 EN Installing The BatteriesFF Button EN4950 EN Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback Feature Playback ZoomEN51 Feature Playback Special EffectsSET REMOTE/VCR Code VCR Code List52 EN Random Assemble Editing R.A.EditVCR other than above JVC VCR equipped with a remote pause connectorEN53 Make ConnectionsSelect Scenes 54 ENAutomatic Editing to VCR EN55Recording deck 56 ENFor More Accurate Editing Diagnosing VCR/CAMCORDER TimingEN57 Adjustment of VCR/CAMCORDER TimingTo hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen  pg58 EN Audio DubbingDark place, or the contrast Focus again  pg Was low Clean the lens and checkCorrective Action Bright60 EN TroubleshootingEN61 62 EN Blink Or channel appropriate Video mode For video playbackEN63 64 EN Press Push Here to close the cassette holder After Use Cleaning The CamcorderPress Battery Release and remove the battery pack Turn off the camcorder345 6 7 # $ % 66 ENEN67 68 EN Approximate zoom ratio Appears during Zooming Appears when Digital Image Stabiliser DIS is engagedAutomatically adjusted EN695Displays the time code 1Displays the sound modeLCD Monitor/Viewfinder Indications During Video Playback LCD Monitor/Viewfinder Indications During D.S.C. PlaybackFunction EN71Mode Remove DUB ErrorCheck TAPE’S Erase Protection Switch Unit in SafeguardTo avoid hazards To prevent damage and prolong service lifeEN73 74 EN Serious malfunctioning EN75About moisture condensation LCD monitor/Viewfinder  pg Indications 76 ENDate/Time Display  pg , 32 Icons  pgTime Code  pg , 25, 32 EN77For Digital Still Camera 78 ENFor General For Digital Video CameraEN79 For ConnectorsGR-DVL200

LYT0583-001A specifications

The JVC LYT0583-001A is a high-performance, versatile component designed for use in various professional video applications, particularly in the realm of broadcasting and videography. It is especially recognized for its notable capabilities in enhancing the image quality of camera systems while ensuring seamless connectivity across different media formats. One of the key features of the JVC LYT0583-001A is its advanced image sensor technology, which allows it to capture incredibly sharp and clear images even in low-light conditions. This sensor utilizes back-illuminated technology, maximizing light sensitivity and enhancing dynamic range, which is critical for professional videographers who often work in challenging lighting environments.

Additionally, the LYT0583-001A supports a wide range of resolutions and frame rates, including high definition and even 4K capabilities. This flexibility provides users with the tools they need to achieve high-quality results in both live productions and post-production processes. The device is also equipped with various output options, including HDMI and SDI, ensuring compatibility with numerous devices and systems within the broadcast industry.

In terms of usability, the LYT0583-001A features a user-friendly interface that allows for easy adjustments and settings modifications. The integration of advanced codec technology enables efficient compression and decompression of video files while maintaining top-notch quality, which significantly benefits storage and bandwidth management.

Moreover, the device’s built-in stabilization technologies offer smooth video capture, reducing the jarring effects often experienced in handheld shooting. This is especially beneficial for action shots or during dynamic camera movement, ensuring a professional finish to every project.

The JVC LYT0583-001A is also designed with durability in mind, making it suitable for various shooting conditions. Its robust construction and weather-resistant features allow it to perform reliably in outdoor environments, enhancing its usability for documentary filmmakers and event videographers.

In conclusion, the JVC LYT0583-001A stands out in the competitive landscape of professional video equipment, offering cutting-edge features and robust performance capabilities tailored to meet the demands of modern content creators. Its combination of advanced imaging technologies, reliable connectivity, and user-friendly operation makes it a worthy investment for any professional aiming to elevate their video production quality.
Top Page Image Contents