Samsung C6435(P) manual Alarm Priority SET, Alarm in SET, Alarm OUT SET, Auto SET, AUX OUT Control

Page 66

ALARM PRIORITY SET

This sets the priority of the 8 ALARM inputs so ALARM can work corresponding to the priority. The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4, ALARM5, ALARM6, ALARM7, ALARM8. If the ALARM is working at the same time and the priority is the same, it will operate according to the DEFAULT priority. While the ALARM is working, it cannot detect

MOTION.

ALARM IN SET

This sets the input TYPE to [NO] (Normal Open), [NC] (Normal Close), or [OFF] depending on the features of the SENSOR connected.

ALARM OUT SET

Each ALARM input corresponds to one of the 3 ALARM OUT.

AUTO SET

This menu designates what to do at the time of ALARM input. Once an alarm is given, the camera will shortly move to the PRESET position corresponding to the respective alarm as follows. PRESET1 to ALARM1~8 PRESET9 to MOTION.

After DWELL TIME at a PRESET position, PATTERN or SCAN will be in action according to the AUTO SET setup.

Setup of OFF/1/2/3/HALF1/HALF2/FULL/SCAN1~4 is available.

OFF dues not perform PATTERN or SCAN after moved to PRESET and each menu has its own function as follows.

PATTERN 1~3 : Preset PATTERN action

HALF1 : Continuous operation of PATTERN1 + PATTERN2

HALF2 : Continuous operation of PATTERN2 + PATTERN3

FULL : Continuous operation of all the above

SCAN 1~4 : Scanning as set

AUX OUT CONTROL

This sets the ALARM OUT motion to continue or act only when the ALARM is working. If it is set to OFF the ALARM OUT motion will operate only when the ALARM is working. (Active “Low”), and if it’s set to ON, the ALARM OUT will always operate regardless of the ALARM.

66

Image 66
Contents SCC-C6433P/C6435P SmartDome CameraSafety Precautions ENG Important Safety Instructions Contents Digital Zoom Display Zoom Display P/T Exit System info Shortcut keys About this guide Main featuresOverview Product overviewNames of Each Part Camera Holder Adapter Camera Body Zoom Lens Cover-domeInitial setting InstallationBefore installation Things to Keep in Mind During Installation and USESetting Communication Protocol Baud Rate Setting Setting RS-422A/RS-485 Termination TX+DATA+ SW1-ON TX-DATA RX+ RX CAMCAM n-1 RS-422A/RS-485 Full Duplex Organization Adapter cable connection Cable connection Video terminal on the rear of monitor BNC CablePower Selection Switch under the Power Adaptor Adapter Cable Controller Installation precautions Separately sold products for installationWall Mount Adaptor SADT-104WM Outdoor Housing SHG-222 Ceiling Mount Adaptor SADT-100CM Corner Mount Adaptor SADT-110CM Installing the camera BRACKET-CEILING BRACKET-CELING ASSY-HOLDER Camera ENG Camera Setup Preset Preset MAP Selectable languages may vary depending on sales region ① Password Undefined ② Password Defined Camera setup Camera IDSync DAY/NIGHT DAY NightAUTO… Motion DET Those 3 types are like the following Block Type Zoom Speed Digital ZoomDisplay Zoom Display ZOOM, you can display the Zoom scale on the screenDisplay P/T ExitVideo set IrisManu Level RET Manu Shutter WDRAGC White BAL ATW2 Focus Mode Oneaf Special Exit Quit MotionWhite BAL Focus Mode Exit Quit RETSpecial Reverse DNRFlickerless DetailPOSI/NEGA SavePreset Position SET Preset IDPreset Speed Video SETZone set Privacy ZoneZone DIR SET Zone Area SET Location Zone Enable Zone ID SETAuto set Auto PANDirection EndlessSpeed Pattern Scan Auto Play Auto PlayAuto Return Play NumberAlarm set Alarm OUT SET Alarm Priority SETAlarm in SET Auto SETTurbo P/T Other setProportional P/T Auto CALCAM Reset FlipLanguage Password Clock set RS-485System info Shortcut keys Auto Return *1 SCC-6435 Product Specifications Details50IRE Size Memo Correct Disposal of This Product