Samsung VKKF004NUS user manual DIY Camera, Changing Remote Control ID, Part Names, Ir Led, Lens

Page 13

Changing Remote Control ID

In a multi-DVR system using a single remote control, you can control only the DVR that matches the ID that you have set using the ID button.

1.Press the [ID] button to check the ID of each of "REMOCON ID" and "SYSTEM ID".

The defaults are 00 for the System ID and 00 for the Remote ID, respectively.

2.To change the Remote ID of the IR REMOTE CONTROLLER, press and hold the [ID] button while entering a desired combination of two digits from 00 to 99.

3.To change the ID of the DVR, refer to "REMOTE CONTROLLER > REMOTE CONTROLLER ID". (Page 28)

4.Press the ID button of the IR REMOTE CONTROLLER to check the ID.

MIf the system number defined in "REMOTE CONTROLLER" is different from the number specified using the remote control, no other button than the [ID] buttons will operate.

DIY CAMERA

Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime. You can also use it indoors as well since it is designed for outdoor use.

Part Names

SOC-A100SOC-A101

b c

 

 

c

 

 

 

 

Name

Description

 

Camera Fitting

Groove that is used to fit the camera bracket.

 

Groove

There exist two grooves; one on the top and one on the bottom.

b

IR LED

These are infrared LED's those are controlled by the illumination sensor.

c

Lens

Focal length of 3.8mm enables you to cover relatively longer range of monitoring.

 

Illumination

Detects incoming light to control the IR LED.

 

Sensor

 

DVR Connection

Connect the cable directly to the DVR without using a particular power cable.

 

Cable

You can use the mini DIN cable to connect to a remote camera.

English _13

OVERVIEW

Lo-Call 1890 866 900

www.cctvireland.ie

Image 13
Contents SDE-120N/SDE-3000N/SDE-3001N SDE-3170P/SDE-3002/SDE-3002P Overview FeaturesOverview Important Safety InstructionsRisk of Electric Shock Do not Open English Before Start BatteryStandards Approvals Package ContentsContents Setup BackupUsing the iPhone Camera SpecificationMenu Part Names and Functions FrontLED Part Names and Functions Rear DVR Remote ControlDIY Camera Changing Remote Control IDPart Names IR LEDCamera Bracket Installing the cameraMini Din Cable Camera Bracket SpecificationAdjusting the Camera Bracket Connecting the Alarm I/O Connecting with other deviceConnecting the alarm Input signal Connecting the alarm output signalNetwork Connection Connecting with Other DeviceLocal System Configuration Internet Total System ConfigurationStarting the System Getting startedLOG on Getting StartedLOG Power OFFLOG OFF Live Live Screen ConfigurationIcons on the Live Screen View the Launcher Menu Display Switching the screen modeRecord Auto SequencePlayback Screen PlaybackTo playback by time option To playback by time selectionBefore Starting Setting UP DVR setupSystem Setup How to use remote control and mouseDATE/TIME SystemYYYY/MM/DD, DD/MM/YYYY, MM/DD/YYYY System Management To update the firmware Remote ControllerTo update the network File in the networkCamera Using the Virtual KeyboardCamera To change the camera titleCovert ColorAudio Connection Motion Sensor SetupTo select a motion area To deselect the motion areaMonitor OSDUse the direction buttons to move to Monitor Adding Sequence SequenceSelect a list to edit Edit window appears When the ADD Sequence window appears, press the ADD buttonSound You can use the remote control to activate the buzzerAudio BuzzerUser Management UserTo add a user account To change the user information User AuthorityNetwork IP SetupTo view the Help DdnsMail Network Connection and SettingsSecurity DVRIf using a router If not using a router for network connectionStatic IP Setup Mode Dynamic IP Dhcp Setup ModeHDD Event Event / SensorDVR Connection Router Port ForwardingEvent / Sensor Alarm InputMode Set the output mode of the alarm Alarm OutputBuzzer OUT Mail Notification Disk Management It will be disabled if Overwrite is set to OFFOverwrite If set to ON, recording will proceed by overwritingTo start the Record Setup Record SetupRecording Operation CONTINUOUS/MOTION Recording To set the record modeTo specify the recording size/FPS/quality Use the direction buttons to move to Alarm Alarm RecordingAdjust the size From the Time bar, select a cell that you want toFrom the Alarm Recording menu screen, select Activation To specify the alarm recording timeYou can specify the recording size in manual recording mode Instant RecordingBackup BackupNEW Backup Release Reserved Data ManagementSearch Search & playSearch by Time PlaybackRight Moves to the rightmost of the log list Search by EventWeb viewer What is web viewer?Introduction System RequirementsWeb viewer To connect to the Web ViewerEnglish Live Viewer At a Glance Live ViewerSelect a channel to display on the screen To record video Switching between split modesTo print the screen Single SplitScreen Capture ActiveX SettingTo view the status To view the logSearch Viewer At a Glance Search ViewerSet the recording properties as necessary TimelineSearch by Event Search by TimeSetup Viewer At a Glance SetupCamera Setting Click the Setup tab to display the DVR remote setup screenMotion setting Color settingOSD setting Audio/Buzzer setting Monitor settingDate/Time setting Management settingRecording Operation Setting Control Device SettingContinuous/Motion Recording Setting Alarm Recording SettingUser Management Setting Instant Recording SettingUser Authority Setting Mail Setting IP Setup SettingHDD Event Setting Alarm Input SettingBuzzer out setting Alarm output settingMail notification setting InformationUsing the iPhone Appendix Camera SpecificationDNR AppendixNtsc / PAL Product Specification SDE-120N/SDE-3000N/SDE-3001N1EA 4CHAVI DHCP, DNS, DDNS, NTP2EA 4EA 2EADetails Model SDE-3170P Product Specification SDE-3170P/SDE-3002P/SDE-3002PAL 1EA BNC 1 Chcvbs2EA 1EA 4EA 2EA 1EAGNU General Public License Open Source License Report on the ProductPreamble Version 2, JuneLo-Call 1890 866 END of Terms and Conditions No WarrantySome devices are designed to deny users access to How to Apply These Terms to Your New ProgramsGNU Lesser General Public License instead of this License Source Code Terms and ConditionsConveying Verbatim Copies Additional Terms Automatic Licensing of Downstream Recipients Acceptance Not Required for Having CopiesUse with the GNU Affero General Public License PatentsRevised Versions of this License Limitation of Liability GNU Lesser General Public LicenseInterpretation of Sections 15 END of Terms and ConditionsLo-Call 1890 866 Modified work must itself be a software library Lo-Call 1890 866 How to Apply These Terms to Your New Libraries Original SSLeay License OpenSSL LicenseLo-Call 1890 866 Correct disposal of batteries in this product Channel DVR TEL +44-1932-45-5300 FAX +44-1932-45-5325 Chertsey, Surrey, United Kingdom KT16 OPS