Kenwood KDC-MP438U Accessories/Installation Procedure, Accessories Installation Procedure

Page 18

Accessories/Installation Procedure

Accessories

Installation Procedure

1.To prevent a short circuit, remove the key from the ignition and disconnect the 8 battery.

2.Make the proper input and output wire connections for each unit.

3.Connect the speaker wires of the wiring harness.

4.Connect the wiring harness wires in the following order: ground, battery, ignition.

5.Connect the wiring harness connector to the unit.

6.Install the unit in your car.

7.Reconnect the 8 battery.

8.Press the reset button.

AWARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

&

Mounting and wiring this product requires skills and experience. For safety'ssake, leave the mounting and wiring work to professionals.

Make sure to ground the unit to a negative 12V DC power supply.

Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit. If the power is not turned ON ("PROTECT" is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.

If your car'signition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

•If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. If the fuse blows, first make sure the wires aren'ttouching to cause a short circuit, then replace the old fuse with one with the same rating.

Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to work if you share the 8 wires or ground them to any metal

part in the car.

•When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the <±)

connector of the left speaker to a front output terminal, do not connect the 8 connector to a rear output terminal.

•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

•Mount the unit so that the mounting angle is 30·or less.

About CD players/disc changers connected to this unit

Kenwood disc changers/ CD players released in 1998 or later can be connected to this unit.

Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. Note that any Kenwood disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. Connecting unsupported disc changers/CD players to this unit may result in damage.

Set the "O-N" Switch to the "N" position for the applicable Kenwood disc changers/ CD players. The functions you can use and the information that can be displayed may differ depending on the models being connected.

18 I KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Kenwood Corporation For your recordsContents Before use Page Page Adjusting the detail of Audio Control Audio ControlYou can set Sound system, such as follows Audio SetupSpeaker Setting English IKDC-X492/KDC-MP438U1KDC-MP408U/KDC-MP338 Enter Switching Display modeGeneral Operation Changes displayed information on each source followingDirect Access Tuning Frequency Step SettingMusic discIAudio file Operation Enter Multi Jog Select mode Press the Mjog button Searching for and playing a songPress the Mjog button Set up the following functions Menu SystemActivating Security Code Manual Clock Adjustment Deactivating Security CodeAuxiliary Input Display Setting Demonstration mode SettingReceive mode Setting Basic Operations of remote control Appendix Swpre Switching Preout Menu GlossaryZONE2 Dual Zone Accessories/Installation Procedure Accessories Installation ProcedureAbout CD players/disc changers connected to this unit Connecting Wires to Terminals ~=LT~----=~~ KDC-MP338Removing the hard rubber frame Non-Japanese carsJapanese cars Removing the UnitTuner source Disc sourceAudio file source Troubleshooting Guide Messages shown below display your systems conditionCD player section FM tuner sectionAM tuner section USB Interface KDC-X492/MP438U/MP408UPage FCC Warning TOKYO, JapanPage Attenzione AchtungAttentie Atencion~\m~1~\\il\\1III I1\\1\11 Atencion Warranty Card Austraua Canada

KDC-MP408U, KDC-MP338, KDC-MP438U specifications

The Kenwood KDC-MP408U, KDC-MP338, and KDC-MP438U are popular models within Kenwood's lineup of car audio receivers. Each of these models delivers a variety of features that enhance your driving experience through superior sound quality and connectivity options.

Starting with the KDC-MP408U, this model is renowned for its versatile playback capabilities. It supports multiple audio formats, including MP3 and WMA, allowing you to play your favorite music files directly from a USB drive or through an auxiliary input. The front USB port enables easy connectivity to smartphones and other devices, while the built-in CD player caters to traditional media users. One of the standout features of the KDC-MP408U is its compatibility with iPod and iPhone, offering USB control that allows you to manage tracks directly from the receiver.

Next, the KDC-MP338 offers a compact design with high functionality and aesthetic appeal. It includes an easy-to-read LCD display that ensures you can navigate through settings and playlists effortlessly. The receivers' CD mechanism supports various disc formats, providing ample options for playback. Users also benefit from a range of sound adjustment features, including a 3-band parametric equalizer that allows for tailored audio experiences based on personal listening preferences. The KDC-MP338 also emphasizes connectivity, with an auxiliary input jack making it simple to connect any device with a headphone output.

The KDC-MP438U builds on the features of its predecessors by infusing additional technologies to enhance usability. In addition to supporting CD, MP3, and WMA formats, it offers Bluetooth connectivity, facilitating hands-free calling and audio streaming from compatible devices. This makes it easier than ever to stay connected while on the road. The KDC-MP438U also includes Kenwood’s proprietary sound features, such as a built-in amplifier that optimizes clarity and sound distribution.

All three models prioritize user-friendly interfaces, ensuring that adjusting settings and playlists is straightforward, even while driving. They include customizable illumination options that allow drivers to match the display color to their vehicle’s interior.

These Kenwood car audio receivers are perfect for audiophiles seeking a blend of innovative features and robust sound quality. Each model retains unique advantages while ensuring that high-quality audio performance stays at the forefront of the driving experience. Whether you're looking for basic connectivity or advanced integration with smart devices, Kenwood offers reliable solutions with the KDC-MP408U, KDC-MP338, and KDC-MP438U.
Top Page Image Contents