Axis Communications P3215-V IPv4 Address Configuration, IPv6 Address Configuration, ARP/Ping

Page 40

AXIS P3215-V Network Camera

System Options

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 48) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 40.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator)

arp -s <IP address> <serial number> ping -l 408 -t <IP address>

Windows example (this may require that you run the command prompt as an administrator)

arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125

4.Check that the network cable is connected and then restart the product by disconnecting and reconnecting power.

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Axis P3215-V Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis P3215-V Network CameraConnectors Performance Considerations Connectors and Buttons Network ConnectorHardware Overview SD Card SlotLED Indicators Color IndicationAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordSet Power Line Frequency Camera OrientationLive View Click Use HttpsGo to Setup Events Controls on the Live ViewAxis Media Control viewer toolbar Manual TriggerPTZ Controls Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P3215-V Network Camera Set Up the Product Basic SetupWhen satisfied, click Enable iris to enable the iris Focus & ZoomVideo Video StreamPixel Counter ImageStream Profiles Click Save to apply the new settings264 Camera Settings Exposure SettingsImage Appearance White BalanceIris adjustment Shutter & GainSet Shutter to Day/NightSelect an Aspect ratio and a Video stream resolution View AreaOverlay Go to Video View AreaUse Overlay Text in an Action Rule Overlay ImageGo to Video Overlay Image Create the action rule Privacy MaskGo to Events Action Rules Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionUser Defined Links Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom Guard TourControl Queue AdvancedControls Detectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis P3215-V Network Camera Install Application Go to Setup ApplicationsApplications Application LicensesAxis P3215-V Network Camera Setting Up an Action Rule EventsAdd Recipients Go to Events Action Rules and click AddSet Up Recurrences Set Up Email RecipientsCreate Schedules Go to Events Schedules and click AddAxis P3215-V Network Camera Recordings Recording ListContinuous Recording Go to Recordings ListLanguages System Options SecurityUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee Basic TCP/IP Settings Go to Setup System Options Security CertificatesDate & Time NetworkIPv4 Address Configuration IPv6 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 BonjourStorage SD CardMount and Unmount SD Card Format SD CardMaintenance Network ShareTo add a network share Go to System Options Storage Click Network ShareSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigScripting File UploadTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, generalVideo Camera Settings Key framesStorage and disk management problems Storage disruptionRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Function/group Specifications System Application InstallationMaintenance General Casing Memory PowerConnectors AccessoriesGeneral accessories Performance ConsiderationsM1.8
Top Page Image Contents