Axis Communications P3214-V user manual Shutter & Gain, Set Shutter to, Iris adjustment, Day/Night

Page 19

AXIS P3214–V Network Camera

Video

Shutter & Gain

The shutter and gain settings affect the amount of motion blur and noise in the image. To adapt to different lighting, available storage space and bandwidth, it is often necessary to prioritize either low motion blur or low noise. The Axis product allows using different prioritization in normal light and in low light.

Shutter speed is related to the amount of time the shutter is opened and is measured in seconds (s). A slow shutter speed allows more light to reach the sensor and can help produce a brighter image in low light situations. On the other hand, a slow shutter speed can cause moving objects to appear blurry.

Set Shutter to

Auto to set the shutter speed automatically. If required, use Max shutter to limit the shutter speed to prevent the frame rate from being reduced. For example, to get 30 fps, set Max shutter to 1/30.

Fixed to use a fixed shutter speed.

Gain, measured in decibel (dB), is the amount of amplification applied to the image. A high gain may provide a better image in low light situations but will increase the amount of image noise.

Set Gain to

Auto to set the gain automatically. If required, use Max gain to limit the applied gain.

Fixed to use a fixed gain.

When Shutter and Gain are both set to Auto, it is possible to set the Priority between low motion blur and low noise manually and to use a different Priority in Normal Light and in Low Light.

Example

Consider an area where people or vehicles move during the day, but where there should be no movements during night. To be able to, for example, recognize faces or license plates, move the normal light priority slider toward low motion blur. At nighttime, motion detection is more important than identification. Motion blur is acceptable and since low light can cause a lot of noise, move

the low light priority slider toward low noise.

Example

If storage space or bandwidth is limited, try using a lower gain. This will reduce image noise and produce smaller image files.

Iris adjustment

Select Enable automatic iris adjustment to automatically compensate for changing light conditions. This option is not available if a fixed iris is used.

Use the Iris adjustment slider to set the preferred F-value. The scale represents the amount the iris is open. If set to 0, the iris is opened as much as possible. If set to 100, the iris is closed as much as possible. The actual F-value is shown below the slider. If automatic iris adjustment is enabled, the iris will stay at this position as long as light conditions are favorable. If light conditions change, the iris will adjust itself to the best iris settings. If automatic iris adjustment is disabled, the iris will lock on the set position regardless of light conditions

Day/Night

The IR cut filter prevents infrared (IR) light from reaching the image sensor. In poor lighting conditions, for example at night, or when using an external IR lamp, set the IR cut filter to Off. This increases light sensitivity and allows the product to “see” infrared light. The image is shown in black and white when the IR cut filter is off.

If using automatic Exposure control, set the IR cut filter to Auto to automatically switch between On and Off according to the lighting conditions.

The Day/Night shift level bar helps determine when the camera will shift from day mode to night mode. Normally, the camera automatically changes mode from day to night when very dark (level 100 in the slider). By setting Day/Night shift level to a lower value, the camera will change to night mode earlier.

19

Image 19
Contents Axis P3214-V Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis P3214-V Network Camera Table of ContentsConnectors Performance Considerations SD Card Slot Connectors and ButtonsNetwork Connector Hardware OverviewColor Indication LED IndicatorsSet the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Set Power Line FrequencyCamera Orientation Live ViewManual Trigger Go to Setup EventsControls on the Live View Axis Media Control viewer toolbarPTZ Controls Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P3214-V Network Camera Focus & Zoom Set Up the ProductBasic Setup When satisfied, click Enable iris to enable the irisImage VideoVideo Stream Pixel CounterStream Profiles Click Save to apply the new settings264 White Balance Camera SettingsExposure Settings Image AppearanceDay/Night Iris adjustmentShutter & Gain Set Shutter toGo to Video View Area Select an Aspect ratio and a Video stream resolutionView Area OverlayUse Overlay Text in an Action Rule Overlay ImageGo to Video Overlay Image Create the action rule Privacy MaskGo to Events Action Rules Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsUser Defined Links Guard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControl Queue AdvancedControls Go to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsAxis P3214-V Network Camera Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P3214-V Network Camera Go to Events Action Rules and click Add Setting Up an Action RuleEvents Add RecipientsGo to Events Schedules and click Add Set Up RecurrencesSet Up Email Recipients Create SchedulesAxis P3214-V Network Camera Go to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardGo to System Options Storage Click Network Share MaintenanceNetwork Share To add a network shareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingCheck the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsReformat the SD card and then click Mount Storage and disk management problemsStorage disruption Re-mount the storage deviceTechnical Specifications Memory Power Function/group Specifications System ApplicationInstallation Maintenance General CasingPerformance Considerations ConnectorsAccessories General accessoriesM1.8