Axis Communications P1427E user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 47

AXIS P1427–E Network Camera

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 40. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 51.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 10.

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The Axis product supports SD cards with the following file systems:

47

Image 47

Contents Axis P1427-E Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P1427-E Network Camera Table of ContentsPerformance Considerations Hardware Overview Connectors and ButtonsNetwork Connector ConnectorColor Indication LED IndicatorsSD Card Slot Control ButtonSet the Root Password Accessing the ProductAccess from a Browser Access from the InternetControls on the Live View Configure Capture ModeSet Power Line Frequency Live ViewManual Trigger Go to Setup EventsAxis Media Control viewer toolbar PTZ Controls Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream Axis P1427-E Network Camera Basic Setup Setting Up the ProductImage VideoVideo Stream Pixel Counter264 Stream ProfilesImage Appearance Camera SettingsCapture Mode Go to Setup Video Camera SettingsShutter & Gain Exposure SettingsWhite Balance Wide Dynamic RangeDay/Night Iris adjustmentSelect an Aspect ratio and a Video stream resolution View AreaGo to Video Overlay Image OverlayOverlay Image Go to Video Video Stream and select the Image tabGo to Events Action Rules Using Overlay Text in an Action RuleGo to Video Focus & Zoom Privacy MaskFocus & Zoom Browser Viewer Description Live View ConfigDefault Viewer for Browsers Viewer SettingsOutput Buttons Go to Setup Live View ConfigUser Defined Links Guard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControls AdvancedControl Queue Go to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsAxis P1427-E Network Camera Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P1427-E Network Camera Events Go to Events Action Rules and click Add Setting Up an Action RuleTime PTZ ControlGo to Events Recipients and click Add RecipientsFallback Action Recipient Use with actionGo to Events Schedules and click Add Setting Up an Email RecipientSchedules RecurrencesAxis P1427-E Network Camera Go to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Go to System Options Storage Click Network Share Network ShareGo to System Options Storage and click SD Card Support MaintenancePorts & Devices File Upload System OverviewLogs & Reports ScriptingPlain Config Reset to Factory Default SettingsUpgrading the Firmware TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Video Camera SettingsStorage disruption Storage and disk management problemsTechnical Specifications Dimensions Function/group Specifications System ApplicationPower ConnectorsConnectors Performance Considerations M1.6