Axis Communications P3364-V user manual Socks, QoS Quality of Service

Page 47

AXIS P3364–V

System Options

Note

H.264 video streams will not be available if the RTSP server is disabled.

SOCKS

SOCKS is a networking proxy protocol. The Axis product can be configured to use a SOCKS server to reach networks on the other side of a firewall or proxy server. This functionality is useful if the Axis product is located on a local network behind a firewall, and notifications, uploads, alarms, etc need to be sent to a destination outside the local network (for example the Internet).

SOCKS is configured under System Options > Network > SOCKS. For more information, see the online help .

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark the following types of traffic: live video, live audio, event/alarm traffic and management traffic.

Note

Live audio DSCP will be equal to live video DSCP if H.264 over RTSP is used.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see . To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 51.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Axis P3364-V Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P3364-V Table of ContentsConnectors Performance Considerations Symptoms, Possible Causes and Remedial ActionsHardware Overview Connectors and ButtonsFor technical specifications, see Hardware OverviewLED Indicators Axis P3364-V Start a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserClick Create self-signed certificate Accessing the Product Access from the InternetSet the Root Password Controls on the Live View Set Power Line FrequencyLive View AMC Audio Controls Axis Media Control viewer toolbarPTZ Controls Half-duplex modeAxis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsBasic Setup Setting Up the ProductSetting Up the Product Image Video and AudioVideo and Audio Video Stream264 Resolution. Select the default resolutionClick Save to apply the new settings Stream ProfilesWhite Balance Camera SettingsExposure Settings Image AppearanceLow light priority slider toward low noise Iris adjustmentShutter & Gain Set Shutter toOverlay To configure the view areaDate/Time Formats in the online help To enable overlays View AreaGo to Video & Audio Overlay Image Privacy MaskFocus & Zoom Overlay ImageAudio Input Audio SettingsAudio Modes Audio Output Audio ClipsDefault Viewer for Browsers Live View ConfigLive View Config Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis P3364-V PTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomGo to PTZ Guard Tour and click Add AdvancedLimits ControlsMotion Detection DetectorsDetectors Camera TamperingParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationApplications ApplicationsAxis P3364-V Events EventsGo to Events Action Rules and click Add Setting Up an Action RulePTZ Control Recurrences RecipientsSchedules Go to Events Recurrences and click Add To set up a recurrenceContinuous Recording RecordingsRecordings Recording ListUsers System OptionsSystem Options SecurityGo to System Options Security Ieee IeeeCertificates Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateSystem Options Network Basic TCP/IP SettingsAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 HttpSocks QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Ports MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P3364-V Checking the Firmware TroubleshootingTroubleshooting Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Troubleshooting Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressBasic Product is accessible locally but not externallyProblems with streaming H.264 Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsTechnical Specifications Technical SpecificationsMaintenance General Casing Function/group Specifications Network SecurityAlarm actions InstallationConnectors Tip Microphone/Line Line out mono Ring Sleeve Ground Mm audio connectors stereoPerformance Considerations Audio Input Audio OutputAxis P3364-V M3.5
Top Page Image Contents