Adjustable Phase Vertical Line Lock AUX

Executing Playback:

1.Press ON, AUX 50, ENTER for continuous playback.

2.Press ON, AUX 51, ENTER for single playback.

Stopping Playback:

1.Press Off, AUX 50 or AUX 51, ENTER or move joystick.

Resuming Playback After Stopping During Playback: 1. After stopping during playback, press On, AUX 52,

ENTER.

Note: If you have moved the AutoDome since stopping, playback will resume where playback was previously stopped.

Adding To Previously Recorded Playback:

1.Execute a single playback.

2.Wait for the playback to end.

3.Press On, AUX 101, ENTER.

4.Begin controlling the AutoDome.

5.At the completion of controlling the AutoDome, press Off, AUX 100 or AUX 101, ENTER.

Changing Ending of Previously Recorded Playback:

1.Execute a single playback.

2.Wait for the playback to reach the point where the change is desired.

3.Press Off, AUX 50 or AUX 51, ENTER to stop playback. This step is optional.

4.Press On, AUX 101, ENTER

5.Begin controlling the AutoDome.

6.At the completion of controlling the AutoDome, press Off, AUX 100 or AUX 101, ENTER.

Erasing A Playback From Some Point

In Playback To The End:

1.Execute a single playback.

2.Wait for the playback to reach the new stopping position.

3.Press Off, AUX 50 or AUX 51, ENTER.

4.Press Set, AUX 500, ENTER.

DIP Switches

S2005.1, S2005.2, and S2005.3: These DIP switches are used to set both the pan and tilt speeds when the dome is being controlled by a system generating "fixed- speed" commands. The table below lists the maximum speeds when the zoom lens is set for full wide angle. The speed automatically decreases from the maximum speed as the lens is adjusted towards the telephoto settings. At its full telephoto setting, the speed will be decreased to approximately 12% of its full wide angle speed.

DIP Switch Settings			Maximum Speed
1	2	3	(°/s)
Off	Off	Off	4
On	Off	Off	6
Off	On	Off	10
On	On	Off	15
Off	Off	On	20
On	Off	On	30
Off	On	On	45
On	On	On	60

If the auto-speed feature is enabled (see DIP switch S2005.4), these DIP switches apply only to the tilt speed.

S2005.4: This switch controls the Auto-speed feature. When on, auto-speed is always enabled and control by AUX 16 is ignored; see Auto-Speed (AUX 16) under SETUP & MAINTENANCE in TC700 Series Camera,

Lens, Pan/Tilt, and Receiver/Driver Modules User’s Manual (TC700-UM) for description. When auto-speed is enabled, the pan speed starts out slowly and increases as the pan control is held on. The speed resets to slow when the pan control is released. The tilt speed is not affected by this switch. It is still controlled by the setting determined by DIP switches S2005.1, S2005.2, and S2005.3. The auto-speed feature is only applicable when the dome is being controlled by a system generating “fixed speed” commands.

S2006.1: RS-232 Baud rate: 2400 - OFF, 9600 - ON

S2006.2: Lens Zoom Polarity

S2006.3: Lens Focus Polarity

S2006.4: Lens Iris Polarity

S2007.1: Not defined, set to OFF

S2007.2: Not defined, set to OFF

S2007.3: Not defined, set to OFF

S2007.4: Not defined, set to OFF

S2008.1: Reserved, set to OFF

S2008.2: Reserved, set to OFF

S2008.3: Reserved, set to OFF

S2008.4: Not defined, set to OFF

Thumbwheel Switch

As Address selector, 0000 responds to all messages regardless of address; otherwise the unit will only respond to commands issued for that address.

Camera Commands

Adjustable Phase Vertical Line Lock (AUX 41)

In multicamera systems using vertical interval switchers, it is desirable to have the video output signals from all cameras vertically synchronized. To achieve synchro- nization, it may be necessary to generate phase delays in some cameras, especially if the cameras receive power from different phases of a 3-phase power source. As shipped from the factory, camera vertical sync is aligned with the positive-going zero crossing of the hot