Samsung SID-50P Installation, Camera Operation, Trobleshooting, Specification, Dimension

Accessories

	M4 Taping Screw 2EA	Cable Rubber
User Manual	Quick Install Guide	Template

INSTALLATION

Installing Camera

1. Fix the camera to a ceiling or a wall using two screws.

2. After fixing it, adjust its pan base and

Notes

•When installing the camera on a ceiling or a wall, not to disturb adjustment of Tilt Base angle fix the BNC-Power Cable on the Pan Base clip.

<Installing the camera on a ceiling> <Installing the camera on a wall>

BNC-Power Cable

Pan Base clip

Connection to Power

For DC Power Type

Resistance of copper wire [at 20C˚ (68˚F)]

Copper wire size (AWG)	#24(0.22mm2)	#22(0.33mm2)	#20(0.52mm2)	#18(0.83mm2)
Resistance ( Ω / m)	0.078	0.050	0.030	0.018
Voltage Drop (V/m)	0.028	0.018	0.011	0.006

•As the voltage drop according to the length of the cable in the above table, a camera may malfunction if there is an excessively long cable run.

*Voltage for camera operation: 12V DC ±10%

*Voltage drops in the above table are variable according to types of cable manufacturer.

Connection to Monitor

Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.

•As a connecting method varies according to instruments, refer to the manual supplied with

Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360°,
Tilting angle: 20˚~90˚)	Tilt Base
	You can adjust up and down
Tilt Base Holding	the camera (20˚~90˚).
Screws

Pan Base	Pan Base Holding Screw
You can rotate the lens
from 360˚

1)	Adjustment Panning angle: After attaching the dome camera to a ceiling or a wall, adjust the
	panning angle for better monitoring area by rotating the Pan Base. The panning angle can be
	adjusted 360˚ freely.
2)	Adjustment Tilting angle: After attaching the dome camera to a ceiling or a wall, adjust
	the tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle can

tilt base properly.

Hole

•Connect the adapter to the power input connector as shown in the figure below. Use a

the instrument.

be adjusted to 20˚ from 90˚ freely. (based the ceiling surface)

3. After adjusting them, secure the shield case and dome-cover.

Screw

Shield Case

Dome Cover

MINI DOME CAMERA 8 USER’S MANUAL

DC12V 500mA. (The Adapter is not provided with the Dome Camera.)

DOME Camera

Adapter (not provided)

Power Input Connector

MINI DOME CAMERA 9 USER’S MANUAL

•Connect the cable after power is turned off.

•Set the 75Ω / Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z and if it is final device, switch it to 75Ω. (Please refer to the Monitor Manual.)

BNC

Intermediate Monitor

DOME Camera

MINI DOME CAMERA 10 USER’S MANUAL

Notes

•After loosening Pan or Tilt Base holding screws, adjust its angle. And then tighten screws again.

•In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.

•This dome camera is to be installed on the ceiling by factory default. In case of using camera on the wall, readjust the Tilt angle as page 8 (Notes).

MINI DOME CAMERA 11 USER’S MANUAL

CAMERA OPERATION

The SID-50 includes the following built in functions

Auto Functions	Setting Value	Descriptions
Electronic Shutter	ESC	The speed is controlled according to the
Speed		brightness of the screen.
WHITE BALANCE		It can be used within the color temperature
	ATW	range 1,800K~10,500K(Ex fluorescent light,
		outdoor, sodium vapor lamp or inside tunnels)
BACKLIGHT	MIDDLE	The gain increases within the range of
		6dB~34dB
GAIN CONTROL	MIDDLE	The gain increases or decreases within the
		range of 6dB~34dB

TROBLESHOOTING

If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician.

The image on the screen is dim.

•Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.

•The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.

The contrast on the screen is too weak.

•Adjust the contrast feature of the monitor.

•If the camera is exposed under too strong light, change the camera position.

•Adjust the lens BACK FOCUS again.

The camera is not work properly, and the surface of the camera case is hot.

• Check that you have connected the camera to a proper power (DC12V ).

SPECIFICATION

ITEM		SID-50N		SID-50P
Power Source		DC 12V±10%/Max. 1.8W
	Total Pixels	811(H) x 508(V)		795(H) x 596(V)
CCD	Effective Pixels	768(H) x 494(V)		752(H) x 582(V)
	SIZE	1/3 inch Super HAD CCD
	Scanning System	2:1 Interlace
Sync.	Synchronization	Internal Only
	Frequency	Horizontal:15.734 KHz/Vertical :59.94	Hz Horizontal: 15.625 KHz/Vertical : 50Hz
	LENS(Built-in)	Built-in Fixed Lens 120		f=3.0mm, F2.0
	Resolution	540 TV Lines(Min.)
E	Video Output	CVBS : 1.0Vp-p/75
L	S/N(Y signal)	50 dB (AGC Off,Weight ON)
E

DECLARATION OF CONFORMITY

Application of Council Directive(s)	89 / 336 / EEC
Manufacturer's Name	SAMSUNG TECHWIN CO., LTD
Manufacturer's Address	SAMSUNG TECHWIN CO., LTD
	42, SUNGJU-DONG CHANGWON-CITY,
	KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment	MINI DOME CAMERA
Model Name	SID-50
Beginning Serial NO.	S6300001
Year of Manufacture	2006. 03. 01
Conformance to	EN 50081-1 : 1992
	EMC-Directive 89/336 EEC and 92/31/EEC
	EN 50130-4 : 1996

SSNR	LOW	There is sufficient reduction in noise levels
(Noise Reduction)		without causing much ghost imaging
		It helps maintain a bright, clear screen image by
SENS UP	ON	automatically detecting changes in the level in
		low light levels without causing much ghost
		imaging.
		The outline of the video image becomes cleaner
SHARPNESS	ON	and more distinctive as the level of
		SHARPNESS increases.

DIMENSION

99.2

63.5

2-Ø 4.2

99.2

99.2

67

C	Min.Illumination		0.05Lux/F1.2(Sens-up), 0.3Lux/F1.2
T			Electronic shutter speed		AUTO
R
I			WHITE BALANCE		AUTO
C	Auto Functions		BACKLIGHT		AUTO
A
			Gain Control		AUTO
L
			SENS-UP		AUTO
			SSNR(Noise Control)		AUTO
			SHARPNESS		AUTO
Monitoring		Pan		Manual 360
Angle		Tilt		Manual 20 ~ 90
Operating temperature/Humidity			-10˚C to +50˚C / 30% to 80% RH
	Dimention		99.2mm(W) x 99.2mm(H) x 67mm(D)
	Weight			200g

We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).

Manufacturer	SAMSUNG TECHWIN CO., LTD	Legal Representative in Europe
Signature		Signature
Full Name	YOUNG TAEK SON	Full Name
Position	QUALITY CONTROL MANAGER	Position
Place	CHANGWON, KOREA	Place
Date	2006. 03. 01	Date

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

MINI DOME CAMERA 12 USER’S MANUAL

MINI DOME CAMERA 13 USER’S MANUAL

MINI DOME CAMERA 14 USER’S MANUAL