American Dynamics ADCTDN0230P, ADCTDN2412N Check the mounting method of the lens before mounting

Page 19

ADCTDN2412N_P_EN.book Page 19 Friday, September 28, 2007 12:49 PM

1.Check the mounting method of the lens before mounting

●This camera is set to CS-mount lens before shipment. To use a C-mount lens, loosen the back focus locking screw with a screwdriver, turn the back focus adjustment ring with your finger or the screwdriver and change the mounting method.

●For the dimension (a) of the lens mounting section as illustrated in the diagram, use the value that is shown in the table below.

Note:

●Never use one that exceeds the dimension (a) as it will damage the inner part of the camera and will not allow normal installation. This will result in a malfunction.

	Lens	Flange back (b)	Dimension (a)

	C-mount lens	17.526 mm	5.5 mm or less

	CS-mount lens	12.5 mm
	CS-mount lens	12.5 mm

2.

3.

Turn the lens clockwise and mount it securely on the camera.

For an autoiris control lens, select the switch on the side of this camera according to the lens used.

VIDEO	: When using a lens with a built-in EE amplifier
DC	: When using a lens without a built-in EE amplifier

4.In the case of an autoiris control lens, check the pin arrangement and connect the lens cable to the socket.

4 pin plug

Pin	DC IRIS lens	VIDEO IRIS lens
number	(Without built-in EE amplifier)	(With built-in EE amplifier)

1	Brake (-)	9.0 V (Max. 50 mA)

2	Brake (+)	NC

3	Drive (+)	VIDEO

4	Drive (-)	GND

19

Image 19

Contents ADCTDN2412N Instructions ADCTDN2412P ADCTDN0230P For USA Important SafeguardsPage Introduction Safety PrecautionsRisk of Electric Shock Do not Open Information for USA Other Countries outside the European Union Power System Day/Night surveillance FeaturesHow to read this manual Conventions and symbols Realizing a High Picture QualityContents Energy Conservation Operating PrecautionsMaintenance Storage and Location of UseOthers Lens Mount Back focus adjustment ringName of Parts and their Functions Front/Bottom/Side panelRotation-preventive hole VIDEO,DC Iris Selector SwitchLevel Iris Level Adjustment Dial Iris Iris Terminal ADCTDN2412 Back panel ADCTDN0230P INT,LL Selector Switch for Synchronizing System AC24V,DC12V Power input terminalVideo OUT Video signal output connector SELECTOR/SET Selector switch/Set buttonMounting Screw for Fall Prevention Wire Power Power indicator lampAC 220 V-240 V power cord Flow for Connection/Settings Mounting the lens Check the mounting method of the lens before mounting Lens Flange back b Dimension aMemo Connecting the back panelAWG18 AWG14 AWG12 AWG10 Connecting the power cableVideo signal coaxial cable ADCTDN2412 AC24 V or DC12 Alarm output terminal Connecting alarm input/output terminalMounting the camera Ask a professional to replace the camera-mounting Mounting the camera-mounting bracket on top of the cameraFall Prevention Precautions regarding fall preventionAdjusting the back focus With a zoom lens With a fixed-focus lensAdjusting the lens Level adjustment Error display Adjusting the AWC one touch manual balanceAWC Error High Light Excessive Illumination Adjustment is completeAWC Error NG Object Object error AWC Error LOW Light Insufficient IlluminationPress the SET button SettingMenu basic operation Press the Menu buttonPress the Menu button again Mode MAX Gain AUX Function TITLE/VIDEO AUX Mode Input PolarityBalance Adjust AWC Execute AWC SET Shutter Gain ModePage AUX Function screen AUX ModeTITLE/VIDEO screen Mode Balance AWCManual ShutterADCTDN2412P/ADCTDN0230P Shutter ManualSpeed ADCTDN2412NGain FIX Gain MAXHigh SuperADCTDN0230P Word Acolorb display differs depending on the modelColor ColourBe absolutely certain of B&W/Color switching, we Color ModeTime Color AutoLevel LOWMonitor BLC ModeDisplay screen OFFCCD Spot LL Adjustment screenMaintenance screen PhaseOUT Title Factory Setting screenCancel ClearwithDetailed setting Camera title settingRepeat steps 2. to How to operate Menu operation StateW.BALANCE Adjust screen is displayed Manual adjustment of white balanceMemo Press the Menu button twice Output of B&W/Color switching signalSetting is complete and the screen returns to the main menu AUX Mode IR Control by B&W/Color switching signal from externalAUX Modeir Input Polarity Make Menureturn Specifications Weight General Power supplyPower consumption Ambient temperature Dimensions Unit mm ADCTDN0230P True D/N Camera