Philips 200VW8FB service manual It is need to Check and repair Monitor

Page 53

General Trouble Shooting Guide

200VW8 LCD

53

9

Picture is too dim

Adjust brightness and/or contrast via the monitor "On Screen Display" or "Front Control Knob".

Is picture displayed

normally?

Note:

1.Sun light passing through a window is much brighter than monitor luminance (luminance is the measurable quantity which most closely corresponds to brightness), therefore the two worst places for a monitor is directly facing the window or directly behind the window. Position the monitor away from these two areas.

YES

END

Is an external Anti-Glare screen

(like protective cover, touch screen...etc) being used?

Remove any external

Anti-Glare screen

Is picture displayed

normally?

*Reset the monitor via OSD manipulation. NO (select Reset to factory settings)

*(or change the color temperature settings to be 9300 color coordination from OSD menu)

 

* Try the monitor with another computer

NO

(video card could be defective)

 

 

 

 

 

 

Is picture displayed

normally?

YES

YES

NO

END

END

It is need to

check and repair

the monitor

Image 53
Contents Service Take care during handling the LCD module with backlight unit Important Safety NoticeGeneral Specification Technical DataSignal Automatic Power SavingData Storage Factory preset mode Pin AssignmentDescription of the On Screen Display Connection to PCConnection to PC Function key definition 200AWSVW8 LCD Advanced OSD Adjustment Advanced OSD AdjustmentClock & Phase Adjustment OSD Attention SignalsOSD Attention signal USE 1680*1050 for Best ResultSafety precautions and maintenance Safety and Troubleshooting InformationInstallation Locations Trouble ShootingOne dark sub pixel Definition of Pixel DefectsDefinition of Pixel Defects Bright DOT Defects Acceptable Level Wiring Diagram Mechnical instructions Mechnical instructions Mechnical instructions Upload instruction Electronic InstructionsDDC instructions General DDC Data Re-programming Electronic InstructionAdditional information System and equipment requirementsRe-programming Analog DDC Installation interfaceRe-programming of writing Hdcp KEY DDC Data DDC dataSafety instruction, warnings and notes Safety Instruction, Warnings and NotesVCC12 Block DiagramCN1 Schematic DiagramScaler Board PowerVGA Schematic DiagramScaler Board Input100/6/NC Schematic DiagramScaler Board ScalerCN2 Schematic DiagramScaler Board PanelAUDIO-IN Schematic DiagramScaler Board AudioCN4 Schematic DiagramPower BoardRTN SEL PWR Schematic DiagramButtom BoardAR9 Layout Side ViewScaler BoardLayout Side ViewScaler Board JP3 Layout Side ViewPower BoardJP9 Layout Side ViewButtom Board AL Foil L7GFCL7G001,REV3AHAN GP Exploded viewRspl for 200VW8FB/00W0ZR-V1C 1 P/N 1W0ZRVPL065CPT Panel Recommended Spare Part ListRspl for 200VW8FB/00W0ZR-V1 N 1W0ZRVPL073AUO & LPL Panel Rspl for 200VW8FB/93W0ZR-V1 N 1W0ZRVPL081AUO & LPL Panel Rspl for 200VW8FB/93W0ZR-V1C 1 P/N 1W0ZRVPL090CPT Panel Main Board Assy Spare Part ListPower Board Assy Chassis Assy Different Part List Inch monitor different parts listGeneral Trouble Shooting Guide General Trouble Shooting Guide END Monitor drivers inf file Try the monitor with another computer Yesno Self test? Picture is too bright Adjust brightness and/or contrast via It is need to Check and repair Monitor Is cabinet Monitor damaged by being dropped? RED + Green + Blue = White OSD Main Menu Locked Please contact your Dealer/reseller for more information Jitter or Noise disappear Consult a service OSD Table of ContentsEnvironment Dimensions of monitor Monitor HousingRelationship Product DataPIN Assignment 1 15 pin mini D-Sub connector LCD specificationGAP definition Panel OffsetOSD Control of OSD Adjustment Parameters Hot-key definition Key Key Press TimeService OSD Message Timeout Menu Power Management Mode Power Specification AC-DC converterOSD Tree 1st Level 2nd Level 3rd Level Up/Down to Move, ok to ConfirmTest equipment Standard Test conditionsVideo Generator test sequence Analog inputTimings Factory preset modes 18 modesPicture performance Audio Specification N/AGeometric defects Picture stability during warm upJitter Viewing angleMissing Pixels / missing subpixel Newton RingContrast ratio White color adjustmentWhite Uniformity Product spec Environmental characteristicsProduction alignment spec Quality Inspection specPower management Safety approvalsCertificates, Reports for the production start Reliability of the monitorRefer to Philips’ definition Safety Check Process