Bose LT 9702, LT 4402, LT MB24 III, LT 9402TM manual Mounting Guidelines

Page 5

Safety Information

Mounting Guidelines

WARNING: The Panaray® LT Series loudspeakers must be attached to brackets or other mounting surfaces for permanent or seasonal use. Such mountings, typically in overhead locations, involve risk of personal injury if either the mounting system or the loudspeaker attachment fails. Installation of the mounting system must be performed in accordance with all applicable building codes including local codes. Consult the local authority before installing this product.

The LT loudspeaker installation requires the use of either Bose® or non-Bose mounting products. While Bose Corporation cannot be held responsible for the proper design and use of non-Bose mounting systems, we offer the following information and guidelines for the permanent installation of your Panaray LT loudspeakers:

•Obtain your mounting system from a reputable manufacturer. Select a system design that works for your loudspeaker and its intended use.

•Before using a custom-designed mounting system, have a licensed professional engineer review the design and fabrication for structural integrity and safety in the intended application.

•The threaded attachment points on the top, bottom, and sides of each loudspeaker have an SAE 3/8-16 inch thread with at least 18 usable threads.

•Lock washers or a locking compound intended for hand disassembly (such as Loctite 242) should be used for a vibration resistant assembly.

•Use a safety cable, separately attached to the cabinet, at a point not in common with the load-bearing attachment points of the mounting system to the loudspeaker. This is recommended even if not required by local regulation. If you are unfamiliar with the proper design, use, and purpose of a safety cable, consult a licensed professional engineer or a rigging professional.

•Additional loudspeakers may be suspended below the Panaray LT loudspeaker provided that:

•It employs all 8 threaded-insert hang points on the top and bottom to fly and suspend the loudspeakers.

•The total weight of suspended loudspeakers and the Panaray LT loudspeaker does not exceed the working load limit (WLL) listed below:

LT 3202®-III Loudspeaker = 395 lb (179 kg)

LT 4402®-III Loudspeaker = 299 lb (135 kg)

LT 9402TM-III Loudspeaker = 261 lb (118 kg)

LT 9702®-III Loudspeaker = 381 lb (173 kg)

LT MB24-III Loudspeaker = 520 lb (236 kg)

CAUTION: Use only graded hardware. Fasteners should be SAE Grade 5 or ASTM designation A354, Grade BC minimum. Unmarked machine fasteners should not be used for mounting system assembly, as there is no way to determine their physical properties. Do not use an M10 fastener; although it is very similar to an SAE 3/8-16, they are not interchangeable. M10 washers may be used in place of 3/8-inch washers.

CAUTION: The fasteners should be tightened using torque not to exceed 50 pounds.inch (5.6 Newton-meters). Over-tightening the fastener could result in irreparable damage to the cabinet and create an unsafe assembly.

CAUTION: The fastener should be long enough to engage no fewer than 16 threads of the attachment point. Using a fastener that is too short provides inadequate holding power and may strip the mounting threads, resulting in an unsafe assembly. Confirm that at least 16 full threads are engaged in your assembly.

CAUTION: Do not attempt to alter the threaded attachment points. Do not attempt to re-thread the attachment points to accommodate any other thread size or type; doing so will compromise the safety of the installation while permanently damaging the loudspeaker.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Bose Panaray LT Series III Loudspeakers Declaration of Conformity Declaration of ConformityContents Read the instructions Safety InformationMounting Guidelines How to Use This Reference Guide LT 3202-III Loudspeaker Mechanical SpecificationsLT 4402 -III Loudspeaker LT 9402-III Loudspeaker LT 9702-III Loudspeaker LT MB24-III Modular Bass Loudspeaker Internal Configurations Acoustical Specifications and WiringRecommended Wire Gauges Acoustical Specifications and Wiring To reconfigure your LT 3202-III loudspeaker only To reconfigure your LT MB24-III modular bass loudspeaker LT 3202-III Acoustical Specifications LT 3202-III Loudspeaker Product DescriptionLT 3202-III Loudspeaker Active Equalization Curves LT 3202-III Loudspeaker ConfigurationsLT 4402-III Acoustical Specifications LT 4402-III Loudspeaker Product DescriptionLT 4402-III Loudspeaker Active Equalization Curves LT 4402-III Loudspeaker ConfigurationsLT 9402-III Acoustical Specifications LT 9402-III Loudspeaker Product DescriptionLT 9402-III Loudspeaker Active Equalization Curves LT 9402-III Loudspeaker ConfigurationsLT 9702-III Acoustical Specifications LT 9702-III Loudspeaker Product DescriptionLT 9702-III Loudspeaker Active Equalization Curves LT 9702-III Loudspeaker ConfigurationsLT MB24-III Acoustical Specifications LT MB24 Loudspeaker Product DescriptionLT MB24-III Loudspeaker Active Equalization Curve LT MB24-III Loudspeaker ConfigurationsOther methods of providing active equalization Active EqualizationLT Series III Mid/High Loudspeakers LT MB24 Modular Bass LoudspeakerPanaray LT Replacement Parts Service InformationPainting Information Service Information Remove the replacement diaphragm from its carton Service Information To Replace the V-2 Mid-frequency Driver in the Panaray LT Service Information Service Information LT 3202-III Loudspeaker Driver and Electronics AssemblyLT 4402-III Loudspeaker 10 11 12 13 14 15 24 23 22 LT 9402TM-III LoudspeakerLT 9702-III Loudspeaker LT MB24-III Loudspeaker
Top Page Image Contents