Samsung SW-232 manual Technical Specifications

Problem	Meaning / Solution
When the MPEG software	Adjust the size of the replay screen.
plays a Video CD, the
	After checking the display resolution, adjust it,
pictures are not regular and
	if necessary.
the running speed is too slow.
The Disc is not in message is	The computer may not recognize the disc if you
displayed even though a disc	start playback too quickly after inserting the disc.
has been inserted.	Open and close the disc compartment and try again.
	Clean the disc and try again.
The CD-R/RW drive is not	The interface mode of the sound card is AT-BUS.
detected after it is connected	You must therefore connect the CD-R/RW drive to
to a sound card.	the IDE port on the PC mother board, rather than
	to the sound card, or install an E-IDE compatible
	sound card.
IN CD has the Formatted	Right-click the mouse on TRAY ICON (right side of
Disc Eject function.	the menu bar at the bottom of the monitor) and then
	select "Eject" to take the CD out.
	Select the drive where the disc is inserted from
	Windows Explorer.
	Right-click the mouse and select "Eject" to take
	the CD out.
When recording NERO,	This seems to occur when you select the recording
it will be recorded not on a	function as the system selects "Image Recorder"
CD but a form of image file.	instead of SW-232.
	In this case, select a recorder from the menu items
	at the upper part of NERO and then select SW-232
	from the Recorder Selection window.
	When installing the recording software, try not to
	install the software before the ROM drive as this
	makes the Image Recorder selected.
The Recorder cannot	Use the firmware automatic upgrade function
recognize the disc.	available at the ODD service website to download
	the newest firmware and then reinstall the recording
	software which is included in the bundle.
	- www.samsungodd.com
	- www.samsungelectronics.com

Technical Specifications

SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice.

	ITEM			SW-232
DISC	Disc types supported	CD-DA, CD-ROM mode 1, CD-ROM XA mode 2, Form 1,
	in read mode	Form 2, CD-Plus, CD-Extra, Photo-CD (Single, Multi-session),
		Video CD ready, Enhanced CD, CD-I/Fmv, CD-R, CD-RW,
		CD-TEXT
	Disc types supported	CD-R, CD-RW
	in write mode
	Erasing disc types	CD-RW
	Disc diameter	120 mm or 80 mm
DRIVE	Data transfer rate	Recording	CD-R :	600 KB/sec. (4X), 1,200 KB/sec. (8X),
PERFORMANCE				1800 KB/sec. (12X), 2,400 KB/sec. (16X),
				3600 KB/sec. (24X), 4,800 KB/sec. (32X),
			CD-R W : 1500 KB/sec. (10X), 600 KB/sec. (4X),
		Reading	CD: CAV 40 Access Time CD-RW : CAV 32 Access Time
			PIO Mode 4:16.6MB/sec,
			Multiword DMA mode 2:16.6MB/sec
	Access time (typical)	110ms (typical)
	Data Buffer	8MB
	Laser	Semiconductor laser
	Slide mechanism	Stepping motor
	Spindle motor	Brushless motor
	Load mechanism	Tray. DC motor (Soft Eject).
ERROR RATE		Mode 1: 1 block/1012, Mode 2: 1 block/109
FRONT PANEL	Eject button	Auto eject or Auto inject
	Indicator	Play / Read (GREEN) Record (RED), Operation LED
	Headphone output	Stereo mini-jack (Ø 3.6 mm) 0.65±20% (vrms) 33Ω
	Volume control	Dial type
REAR PANEL	Required power	+5 VDC: 1.5 A (max.), +12 VDC: 1.5 A (max.)
	Interface connector	ATAPI (E-IDE)
	Audio output	Line out 0.75±20% (vrms) : 47KΩ
	Jumper block	Device configuration jumper
OPERATING	Operations	Temperature:		5~45°C	Humidity: 10~80%
ENVIRONMENT
	Storage	Temperature: -25~55°C			Humidity: 10~90%
GENERAL	Dimensions	148.2 (W) x 42 (H) x 184 (D) mm (including bezel)
	Net weight	765 g
RELIABILITY	MTBF	125,000 POH(Duty 20%)

ENGLISH

16 17