QSC Audio WL118-SW, WL-2082-i owner manual Specifications

Specifications

	WL2082-i			WL118-sw
Configuration	3-way, bi-amp or tri-amp mode			Vented box
Transducers
High-frequency	Dual 50 W, 8Ω 1" exit, 1.75" titanium diaphragm, neodymium			—
	magnet assembly
Low-frequency	Dual 200 W, 16Ω 8" woofer, 2" voice coil, neodymium magnet			850 W, 8Ω 18" woofer with a 4" voice coil, ceramic
	assembly, weather resistant cone			magnet assembly
Frequency Response (±3 dB)	80 Hz – 20 kHz			32 Hz – 200 Hz
Frequency Range (-10 dB)	68 Hz – 22 kHz			29 Hz – 800 Hz
Nominal Impedance	HF: 16Ω			—
	LF bi-amp mode: 8Ω			—
	LF tri-amp mode: 16Ω (x 2)			LF: 8Ω
Continuous Power Capacity1/ Recommended Power	HF: 100 W / 200 W			—
	LF bi-amp mode: 400 W / 800 W			—
	LF tri-amp mode: 200 W / 400 W (x 2)			LF: 850 W / 1750 W
Sensitivity (1 W at 1 m)	HF: 106 dB			—
	LF: 96 dB			LF: 98 dB
Maximum Output Continuous / Peak (SPL at 1 m)	HF: 126 dB / 132 dB			—
	LF: 122 dB / 128 dB			LF: 128.5 dB / 134.5 dB
Nominal Coverage	H: 140°			—
	V: dependent on number of elements used			—
Cabinet Type	Ported, elliptical / trapezoidal			Vented subwoofer
Enclosure Material	HIPS (high impact polystyrene) with UV protectant			18 mm Baltic birch plywood
Finish	Available in black (WL2082-i BLK) or white			Available in black (WL118-sw BLK) or white
	(WL2082-i WHT) paintable			(WL118-sw WHT) paintable
Grille	Perforated, formed aluminum			16 gauge powder-coated steel with cloth backing
Connectors	2 x NL8 in parallel			2 x NL8 in parallel / 2 x NL4 in parallel
Pin Outs	Pins	Bi-Amp	Tri-Amp	Pins (NL8)		Pins (NL4)
	1+/1-	NC	NC	1+/1-	Sub	1+/1-	Sub
	2+/2-	NC	LF2	2+/2-	Pass thru	2+/2-	Pass thru
	3+/3-	LF	LF1	3+/3-	Pass thru
	4+/4-	HF	HF	4+/4-	Pass thru
Attachment Points	Integral, side plate adjustable rigging system, vertical splay			Integral, non-adjustable (straight array only)
	adjustable in 1° increments from 0° – 10°
Weight (Net / Shipping)	37 lb (16.8 kg) / 45 lb (20.45 kg)			111 lb (50.4 kg) / 121 lb (55 kg)
Dimensions (HWD)	11.8" x 27" x 13.4" (300 mm x 686 mm x 340 mm)			22.1" x 27.6" x 30.3" (562 mm x 702 mm x 771 mm)
Accessories Available	FB2082-i: Fly-bar for WL2082-i, WL118-sw and WL115-sw. Available in black or white.
	EB2082-i: Extension bar, allows WL118-sw or WL115-sw to be suspended behind WL2082-i. Available in black or white.

PB2082-i: Pullback bar for WL2082-i. For use when pulling back the bottom of the array is necessary to achieve the desired angle. Available in black or white.

AB2082-i: Angle bracket, allows greater vertical splay between WL2082-i and WL118-sw or WL115-sw enclosures in ground stacked configurations. Available in black. Requires two brackets per array, sold individually.

GS115-sw: Ground stack kit for WL118-sw or WL115-sw.

QRP-KIT-1: Kit of four (4) Quick Release Pins for use in lieu of included bolts.

1) 2 hours, IEC specified noise

Specifications subject to change without notice.