Amplifier Owner’s Manual
SPECIFICATIONS
SD800.4 SPECIFICATIONS
Frequency Response: | ± 1dB from 20Hz to 20kHz | RMS Power Output | 125w x 4 @ 4 ohms Stereo |
Signal to Noise Ratio: | >100dB |
| 200w x 4 @ 2 ohms Stereo |
High and Low Pass Crossovers: | 12dB per Octave |
| 400w x 2 @ 4 ohms Bridged |
Crossover Range: | 40Hz to 400Hz |
|
|
Bass Boost @ 45Hz: | 0 to +18dB | Power/Ground Wire Size: | 4 Gauge |
Low Level Input Range: | 200 millivolts to 8 volts | Recommend Power Wire Fuse: | 60a |
Lowest Recommend Load: | 4 ohms Bridged/2 ohms Stereo | Dimensions (Includes Mounting Feet): 11.0” L x 6.9”W x 2.0” H | |
Typical Efficiency: | 80% |
| 279mm L x 176mm W x 51mm H |
Damping Factor | Greater than 200 | Dimensions (Includes Terminals): | 11.6” L x 6.9”W x 2.0” H |
|
|
| 295mm L x 176mm W x 51mm H |
SD1100.5 SPECIFICATIONS
FRONT AND REAR CHANNELS: |
| RMS Power Output | 125w x 4 | @ 4 ohms Stereo |
Frequency Response: | ± 1dB from 20Hz to 20kHz | |||
Signal to Noise Ratio: | >100dB |
| 200w x 4 | @ 2 ohms Stereo |
High and Low Pass Crossovers: | 12dB per Octave |
| 400w x 2 | @ 4 ohms Bridged |
Front/Rear High Pass Crossover Range: | 15Hz to 250Hz |
|
|
|
Low Level Input Range: | 200 millivolts to 8 volts |
|
|
|
Lowest Recommend Load: | 4 ohms Bridged/2 ohms Stereo |
|
|
|
Typical Efficiency: | 80% |
|
|
|
Damping Factor | Greater than 200 |
|
|
|
SUBWOOFER CHANNEL: |
|
Frequency Response: | ± 1dB from 20Hz to 300Hz |
Signal to Noise Ratio: | >100dB |
Low Pass Crossover: | 12dB per Octave |
Low Pass Crossover Range: | 30Hz to 300Hz |
Bass Boost @ 45Hz: | 0 to +18dB |
Low Level Input Range: | 200 millivolts to 8 volts |
Lowest Recommend Load: | 2 ohms |
Typical Efficiency: | 80% |
Damping Factor: | Greater than 200 |
RMS Power Output | 200w x 1 @ 4 ohms |
| 300w x 1 @ 2 ohms |
Recommend Power Wire Fuse: | 80a |
Power/Ground Wire Size: | 4 Gauge |
Dimensions (Includes Mounting Feet): 12.2” L x 6.9”W x 2.0” H | |
| 309mm L x 176mm W x 51mm H |
Dimensions (Includes Terminals): | 12.8” L x 6.9”W x 2.0” H |
| 325mm L x 176mm W x 51mm H |
POWER OUTPUT NOTE: A power birth certificate is included for each amplifier. SD amplifiers are conservatively rated and will exceed their RMS power rating shown here. All RMS power ratings and measurements are at 14.4 volts with no more than 1% THD. SD800.4 and SD1100.5 feature ADAPT technology which provides the same power output from 11 to 15 volts with music material.
www.phoenixgold.com