Step By Step Installation

●RTA (real time analyzer)

●Soldering iron and solder

●Utility knife

●Wire brush or sandpaper for chassis grounding

●Wire crimper

●Wire cutters

●Wire strippers

Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information.

Step 2 Decide on the system configuration for your amplifier. For system sugges- tions, refer to the Speaker Connections section of this guide.

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and battery. Do not connect the battery at this time. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great potential for induced system noise.

Step 4 Pre-drill amplifier mounting holes. Be sure to "think before you drill". Gas tanks, fuel lines, and other obstructions have a nasty way of hiding them- selves. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit.

Step 5 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.

Step 6 Turn the vehicle's key switch to the off position.

Step 7 Disconnect the vehicle's battery ground terminal.

Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM).

Step 9 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this guide for correct wiring instructions.

Connect the ESP®-2 cable that came with the amplifier from the amplifier’s ESP port to the security system’s ESP port.

Step 10 Reconnect the ground terminal to the battery after power, speaker, and RCA connections are completed.

Step 11 Set crossovers. Refer to the Internal Crossover Configuration section of this manual for detailed instructions.

Step 12 Once satisfied that all connections and settings are correct, install the fuse located near the vehicle's battery and proceed to the Testing the System sec- tion of this manual.

WARNING! Never exceed the recommended fuse size of this amplifier. Failure to do so will result in the voiding of your warranty and possible damage to the amplifier.

HCCA-D5000, HCCA-D2400, HCCA-D1200, HCCA-D1200, HCCA-D2400, HCCA-D5000 specifications

Orion Car Audio has long been a respected name in the car audio industry, known for producing powerful and high-quality amplifiers. Among its standout products are the HCCA-D1200, HCCA-D2400, and HCCA-D5000 amplifiers, each designed to deliver exceptional performance and clarity in audio reproduction.

The Orion HCCA-D1200 is a formidable amplifier that offers a power output of 1,200 watts RMS at 1 ohm. It is tailored for those seeking a robust sound system that prioritizes low-frequency performance. This model features a high-efficiency Class D design, enabling it to transmit clean power with minimal distortion. With adjustable gain control, low-pass and subsonic filters, users can easily tailor the sound to suit their preferences.

Moving up in the lineup, the HCCA-D2400 stands as a powerhouse capable of delivering 2,400 watts RMS at 1 ohm. This amplifier is built with a heavy-duty heat sink and high-quality internal components, ensuring durability and reliability even under heavy loads. The HCCA-D2400 is designed with an advanced PWM MOSFET power supply, enhancing the overall efficiency. Its comprehensive crossover system allows for precise audio tuning, catering to both casual listeners and audiophiles.

For those who demand the ultimate in power, the HCCA-D5000 is a top-tier choice. This beast of an amplifier provides an astounding 5,000 watts RMS at 1 ohm, making it ideal for competitive setups and serious bass enthusiasts. The HCCA-D5000 features an ultra-efficient design that minimizes power loss, paired with a low-level input sensitivity that maximizes compatibility with various signal sources. Its built-in protection circuitry safeguards against overheating and short circuits, adding a layer of reliability.

All three models emphasize Orion’s commitment to high-quality construction and innovative technology. They utilize a unique low-frequency response, ensuring that bass notes are rendered with depth and clarity. Together, the HCCA-D1200, HCCA-D2400, and HCCA-D5000 represent an impressive lineup, catering to clients with varying needs and preferences.

Whether enhancing a daily driver or building a competition-grade sound system, the Orion HCCA series amplifiers provide the power, clarity, and reliability that enthusiasts demand. With their striking performance characteristics and user-friendly features, they embody the essence of what Orion Car Audio stands for in the competitive landscape of car audio equipment.