Orion Car Audio HCCA-D5000, HCCA-D1200, HCCA-D2400 manual Directed Electronics, all rights reserved

Page 22

NOTE: Use caution when adjusting or unlocking gain as restricting the range or unlock- ing the range can result in sudden increases in gain.

The Valet Monitoring and Anti Theft options (below) require the ESP2 alarm to be “learned” into the amplifier. Prior to setting the valet or anti theft to Enable or On, execute the TXID routine. The ESP2 alarm must be the one installed in the vehicle.

Valet Monitoring - Disable, Enable. Used in conjunction with an ESP®-2 security system to prevent operation of the amplifier when the security system is in Valet mode. When Valet mode is Enabled, and the valet code is received from the alarm system, the amplifier will not power up the next time it goes through a remote line On cycle (using the head unit or other device that turns the amplifier on).

Anti Theft - Off, Reserved, On. When set to “On”, and when the ESP®-2 security system is armed, the amplifier will not operate until the security system is disarmed (the remotes used by the security system must be learned by the amplifier—see “Learn TX IDs” below). If the security system is armed and then the amplifier is disconnected from 12V DC, the amplifier will be locked out from operation. You can reset the amplifier by disarming the security sys- tem (it must be one of the transmitter learned by the system), then cycling the remote power on/off.

Top Light Options - Light Off W/Service Code, Light On W/Service Code, Light Off W/O Service Code, Light On W/O Service Code. This feature allows the toplight to duplicate the function of the ESP status indicator. This is set by the W/Service Code. The toplight may also be turned off if desired (Light On/Light Off) independent of the Service Code (see table below).

1.

Light Off W/Service Code

Top light is off, but service codes will be shown.

 

 

 

2.

Light On W/Service Code

Top light is on, and service codes will be shown.

 

 

 

3.

Light Off W/O Service Code

Top light is off, but service codes will not be shown.

 

 

 

4.

Light On W/O Service Code

Top light is on, but service codes will not be shown.

 

 

 

Learn TX IDs - Off, On. When On learns the amplifier learns the remotes (press arm and then disarm on just one of the remotes) used by a Directed Electronics ESP®-2 security system. If any remotes are added or replaced in the system your vehicle must be returned to the deal- er to have the amplifier learn the new/replaced remotes. The installer uses the following procedure to learn the security system’s remotes:

1.Unplug the amplifier ESP®-2 port from the security system.

2.Connect the Bitwriter® to the amplifier ESP®-2 port using the cable that came with the Bitwriter®.

3.Turn on the Bitwriter® and read the file from the amplifier.

4.Scroll down to Learn TX IDs and select the On setting.

5.Unplug the Bitwriter® and reconnect the ESP®-2 cable from the security system.

6.Arm the security system (the amplifier ESP® LED will flash), then disarm the secu- rity system. The remotes used with the security system are now learned into the amplifier. After a short time frame (approximately 20-seconds) the Learn TX IDs feature will automatically revert back to the default Off setting.

NOTE: The next three features are read only. The amplifier will not permit them to be changed. If a change is attempted, an “Unable to Verify” error message will appear on the Bitwriter®.

© 2005 Directed Electronics, all rights reserved

21

Page 21 Page 23
Image 22
Page 21 Page 23
Contents HCCA-D1200 HCCA-D2400 HCCA-D5000 Contents Important Note IntroductionWhat’s in the Box Record Your Serial Number and Date Practice Safe SoundEND Panel Layouts HCCA-D2400 CEA Specifications Specifications Amplifier Section HCCA-D1200 HCCA-D2400 HCCA-D5000Amplifier Settings Low-Pass Crossover Fine Tuning the CrossoversAdjusting INTELLi Q High-Pass CrossoverInfinite Baffle Example High-Pass Set at 30Hz Enclosure Type Boost LevelsSealed Example High-Pass Set at 30Hz Sealed Example High-Pass Set at 20HzVented Example High-Pass Set at 30Hz Power Connections for the HCCA-D5000 Amplifier WiringPower Connections for the HCCA-D1200, and HCCA-D2400 Remote Gain OperationSpeaker Connections BridgingPassenger Compartment Amplifier InstallationChoosing Mounting Locations Trunk CompartmentGeneral Precautions and Installation Tips Tools of the TradeStep By Step Installation Testing the System SET UP and TroubleshootingAdjusting the Sound of the System Directed Electronics, all rights reserved Troubleshooting Tips Symptom Probable Cause Action To TakeInternal Crossover Configuration APPENDIX-PROGRAMMABLE Features Directed Electronics, all rights reserved Directed Electronics, all rights reserved Directed Electronics, all rights reserved Warranty

HCCA-D5000, HCCA-D2400, HCCA-D1200, HCCA-D1200, HCCA-D2400, HCCA-D5000 specifications

Orion Car Audio has long been a respected name in the car audio industry, known for producing powerful and high-quality amplifiers. Among its standout products are the HCCA-D1200, HCCA-D2400, and HCCA-D5000 amplifiers, each designed to deliver exceptional performance and clarity in audio reproduction.

The Orion HCCA-D1200 is a formidable amplifier that offers a power output of 1,200 watts RMS at 1 ohm. It is tailored for those seeking a robust sound system that prioritizes low-frequency performance. This model features a high-efficiency Class D design, enabling it to transmit clean power with minimal distortion. With adjustable gain control, low-pass and subsonic filters, users can easily tailor the sound to suit their preferences.

Moving up in the lineup, the HCCA-D2400 stands as a powerhouse capable of delivering 2,400 watts RMS at 1 ohm. This amplifier is built with a heavy-duty heat sink and high-quality internal components, ensuring durability and reliability even under heavy loads. The HCCA-D2400 is designed with an advanced PWM MOSFET power supply, enhancing the overall efficiency. Its comprehensive crossover system allows for precise audio tuning, catering to both casual listeners and audiophiles.

For those who demand the ultimate in power, the HCCA-D5000 is a top-tier choice. This beast of an amplifier provides an astounding 5,000 watts RMS at 1 ohm, making it ideal for competitive setups and serious bass enthusiasts. The HCCA-D5000 features an ultra-efficient design that minimizes power loss, paired with a low-level input sensitivity that maximizes compatibility with various signal sources. Its built-in protection circuitry safeguards against overheating and short circuits, adding a layer of reliability.

All three models emphasize Orion’s commitment to high-quality construction and innovative technology. They utilize a unique low-frequency response, ensuring that bass notes are rendered with depth and clarity. Together, the HCCA-D1200, HCCA-D2400, and HCCA-D5000 represent an impressive lineup, catering to clients with varying needs and preferences.

Whether enhancing a daily driver or building a competition-grade sound system, the Orion HCCA series amplifiers provide the power, clarity, and reliability that enthusiasts demand. With their striking performance characteristics and user-friendly features, they embody the essence of what Orion Car Audio stands for in the competitive landscape of car audio equipment.
Top Page Image Contents