Orion Car Audio 2500D, 600D, 1200D manual SET UP and Troubleshooting, Testing the System

Page 16

amplifier is twisted or bent.

Step 6 Turn the vehicle's key switch to the off position.

Step 7 Disconnect the vehicle's battery ground terminal.

Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM).

Step 9 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this guide for correct wiring instructions.

Step 10 Reconnect the ground terminal to the battery after power, speaker, and RCA connections are completed.

Step 11 Set crossovers. Refer to the Internal Crossover Configuration section of this manual for detailed instructions.

Step 12 Once satisfied that all connections and settings are correct, install the fuse located near the vehicle's battery and proceed to the Testing the System sec- tion of this manual.

WARNING! Never exceed the recommended fuse size of this amplifier. Failure to do so will result in the voiding of your warranty and possible damage to the amplifier.

SET UP AND TROUBLESHOOTING

Testing the System

After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion system.

Step 1 Check all the wiring connections to be sure they are correct and secure.

Step 2 Turn the signal source volume control all the way down. Set any tone con- trols to their flat or defeated positions. This includes the loudness control.

Step 3 Turn the level controls of the amplifier to their minimum positions.

Step 4 Turn the source unit on. Check to see if the power LED located on the con- nection side of the amplifier is on. If not, please refer to the Power Connections and the Troubleshooting Tips sections of this manual for instruc- tions.

Step 5 If using an aftermarket source unit, turn the level controls of the amplifier about one quarter of a turn. Slowly increase the volume level of the source unit to so that you can hear the output of the system. If no sound is heard or if the output is distorted, turn the system off immediately. Refer to the Power Connections and the Troubleshooting Tips sections of this manual to solve your installation problems.

Step 6 Check to make sure the output for each channel is correct. If the active crossovers are used, check to make sure that each output is correct from the amplifier. When using active crossovers on midrange and tweeters, do not use crossover frequencies lower than recommended. If the system is not con- figured properly, refer to the Internal Crossover Configuration section of this manual and take corrective action.

Step 7 If the output is clear and undistorted, continue to the Adjusting the Sound of the System section of this manual.

©2003 Directed Electronics, Inc.

15

Image 16
Contents Page Contents Practice Safe Sound IntroductionWhat’s in the Box Limited TWO-YEAR Consumer Warranty Record Your Serial Number and DateAmplifier Section Orion 600D Orion 1200D Orion 2500D SpecificationsCrossover Section END Panel Layouts Directed Electronics, Inc Amplifier Settings Fine Tuning the Crossovers Adjusting INTELLi QLow-Pass Crossover High-Pass CrossoverInfinite Baffle Example High-Pass Set at 30Hz Enclosure Type Boost LevelsSealed Example High-Pass Set at 30Hz Sealed Example High-Pass Set at 20HzVented Example High-Pass Set at 30Hz Amplifier Wiring Power Connections for the 600D and 1200DPower Connections for the 2500D Remote Gain OperationSpeaker Connections BridgingAmplifier Installation General Precautions and Installation TipsChoosing Mounting Locations Passenger CompartmentStep By Step Installation Tools of the TradeSET UP and Troubleshooting Testing the SystemAdjusting the Sound of the System Troubleshooting Tips Symptom Probable Cause Action To TakeInternal Crossover Configuration Directed Electronics, Inc Directed Electronics, Inc Warranty