Getting AC Power To The PR15P | Peavey PR 15P specs

Getting AC Power To The PR™15P

The PR™15P comes with an 8-foot IEC connection AC power cord. If you are using an extension cord or power strip with this powered speaker, make sure it is of good quality and of a sufficient current capacity to maintain safety and maximize the power output capability of the PR 15P. Do not connect any other device to the same extension cord that the PR 15P is connected to.

Special Note for Permanent Installation

When installing the PR 15P, AC power runs will be used and a certified electrician should be consulted to be sure that all AC wiring complies with local codes and regulations. It is also advisable to use a cable clip properly affixed to the cabinet to strain relief the IEC power cord connected to the amplifier module at (2) so the power cord cannot be pulled out or vibrate loose.

Use of PR 15P with a Subwoofer

The built-in pole adapter allows use with the Peavey SP Subcompact 18X and the accessory pole that it is designed to use, Peavey part #00326540.

The pole used is 36-3/16" long and has a nominal diameter of 1-3/8".

Getting a Signal to the PR 15P

There are a variety of ways to input a signal to the PR 15P.

The primary input (5) provides either a balanced mic- or line-level input, allowing the use of a 1/4" phone plug, either a standard single-ended (tip-sleeve) plug or a balanced TRS (tip-ring-sleeve) type plug OR a male XLR plug. Then there are two line-level unbalanced 1/4" phone jacks that can be mixed in with the primary input.

Do not connect cables to the jacks while the unit is ON and the Volume is turned up!

While a standard single-ended 1/4" phone plug-equipped cable will work well and the balanced input circuitry of the primary input (5) will provide some interference rejection, a balanced cable using either the balanced TRS 1/4" phone plug or the XLR plug will provide superior interference rejection and performance. Sometimes, with difficult interference problems, it will be helpful to lift the shield ground on a balanced cable at the PR 15P end only. Check any input changes carefully, always turning the volume control down before plugging and unplugging cables.

Use of high quality, premium cables is recommended for the PR 15P, as these usually have better shielding and materials and will provide greater long-term reliability. It is usually a good idea to leave some slack at the input to the PR 15P and also to tape the cables down or run them under a cable guard to avoid anyone tripping over them or pulling the PR 15P over when stand mounted.

Volume Control Adjustment

The PR 15P is equipped with a volume control to facilitate use in many different applications. With the volume control adjusted fully clockwise, gain is at maximum and the input sensitivity is 0.375 V RMS for full-rated output. When driving the PR 15P from a mixer, it may be advantageous to reduce the input sensitivity by turning the volume control to the halfway point. The PR 15P will now more closely match a typical power amp.

If the mixing board indicates clipping of its output signals, then all of the PR 15P power capability is not being utilized cleanly. Clipping the signal before it gets to the PR 15P is not optimal. In that case, reduce the mixer output level and turn up the volume control on the PR 15P.

The amplifiers in the PR 15P are equipped with DDT™ and an LED indicator to show that DDT™ has engaged. If the sound seems heavily compressed, check this indicator; and if it is blinking RED more than occasionally, then the drive level from the mixer (or the volume control on the PR 15P) needs to be reduced.

PR 15P specifications

The Peavey PR 15P is a popular powered loudspeaker designed for musicians, DJs, and sound engineers seeking a versatile and robust solution for live sound applications. With its impressive audio performance and durable construction, the PR 15P stands out as a reliable choice for both professional and amateur use.

One of the key features of the PR 15P is its 15-inch heavy-duty woofer that provides deep, punchy bass response. Coupled with a 1-inch compression driver and a high-frequency horn, the speaker delivers clear and articulate high frequencies, ensuring a balanced sound across the entire frequency range. The combination of these components allows the PR 15P to produce a powerful output of up to 1000 watts peak power, making it suitable for large venues or outdoor events.

The PR 15P is equipped with a built-in class D amplifier, which not only provides efficient power but also contributes to a lightweight design. This amplification technology allows the speaker to deliver exceptional sound quality without the bulkiness often associated with traditional amplifiers. The enclosure is constructed from durable polypropylene, ensuring the speaker can withstand the rigors of transport and frequent use.

In terms of connectivity, the PR 15P offers versatile options that include XLR and 1/4-inch inputs, allowing users to connect a variety of audio sources such as mixers, microphones, or instruments. The presence of a built-in mixer with a 3-channel configuration adds to its functionality, making it an all-in-one solution for smaller setups. Additionally, a simple adjustable EQ allows users to tailor the sound according to their specific environment or preferences.

The design of the Peavey PR 15P also features a lightweight construction and ergonomically placed handles, which facilitate easy transport and setup. The speaker can be used in multiple configurations, including as a main PA speaker, a floor monitor, or even mounted on a standard speaker stand.

Overall, the Peavey PR 15P combines powerful performance, versatility, and portability, making it an ideal choice for a wide range of sound reinforcement applications. Its robust features and technologies ensure that users can achieve professional-grade sound quality, whether in a club, at a concert, or during a corporate event. The PR 15P truly exemplifies Peavey’s commitment to delivering high-quality audio solutions for both performers and audiences alike.