Onkyo CR-505DAB instruction manual Abnormal Behavior, Restoring the Default Settings

Page 39

Troubleshooting—Continued

 

 

Trouble

 

 

Possible Cause

 

 

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The CR-505DAB was already on at the

Set the CR-505DAB to Standby (page 33).

 

 

 

The CR-505DAB must be in Standby mode,

 

 

 

specified ON time.

 

 

 

otherwise the timed task will not work.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

 

-connected cassette tape deck or

You must set the recording devices to standby

 

 

 

 

The timer didn’t work?

MD recorder had not been in standby mode.

mode too.

 

 

 

 

 

 

 

 

 

 

 

The specified ON time coincided, or over-

Check the timer settings and correct as neces-

 

 

 

 

 

 

lapped the ON time of another timer.

sary (page 34).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The CR-505DAB is only connected digi-

To make recordings with

 

-connected MD

 

 

 

 

 

 

 

recorder, connect the recorder’s analog inputs

 

 

 

tally to the MD recorder.

 

 

 

to the CR-505DAB’s analog outputs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

While a timed recording task is in progress,

To hear what’s being recorded, press the

No sound is output when a

[MUTING] button to cancel the Mute func-

the output of the CR-505DAB is muted.

timed playback or record-

tion. Press it again to mute the CR-505DAB.

 

 

 

ing task starts?

For timed playback, the volume is deter-

Set the volume to a suitable level (page 19).

 

 

 

mined by the [VOLUME] control.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

There’s no RCA/phono analog audio con-

To use

 

you must make an analog audio

 

 

 

 

 

 

 

 

 

 

doesn’t work.

connection (RCA/phono) between CR-

 

 

 

 

nection.

 

505DAB and your Onkyo components even if

 

 

 

 

 

 

 

 

 

 

they are connected digitally.

 

 

 

 

 

 

 

 

 

 

 

 

Standby indicator flashes.

The protection circuit may be activated.

Make sure not to short-circuit the positive and

negative speaker wires.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Abnormal Behavior

The CR-505DAB contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.

Restoring the Default Settings

To reset the CR-505DAB to its factory defaults, turn it off and unplug the power cord. Then press and hold the [STANDBY/ ON] button on the CR-505DAB, and plug in the power cord.

39

Image 39
Contents CR-505DAB Avis Important Safety InstructionsFor British models PrecautionsMemory backup PrecautionsTable of Contents DAB antenna FeaturesSupplied Accessories AM loop antenna FM indoor antennaRemote control Sensor Before Using the CR-505DABInstalling the Remote Controller Batteries Using the Remote ControllerFront Panel Controls & ConnectorsRear Panel Remote Controller Up & Down buttons- Used to set the tim- ersInput selector buttons- Used to select sound sources Strip 10 mm from End of each cord Connecting Your SpeakersConnecting the Speaker Cords to the Speaker Connectors Powered SubwooferPush Insert wire Connecting an AntennaConnecting the Indoor FM Antenna Connecting the AM Loop AntennaUsing a TV/FM Antenna Splitter Connecting an Outdoor FM AntennaConnecting an Outdoor AM Antenna Connecting the DAB AntennaLeft white Right red Wrong Cassette Tape Deck Connecting Your Other Components to the CR-505DABBefore Making Any Connections Analog audio Left white Right redConnecting -compatible Components Accuclock Function Powering Up and Setting the ClockPowering Up the CR-505DAB Connect the power cord to a suitable wall outletSetting Accuclock to Use a Specific Station Powering Up and Setting the ClockTurning Off Accuclock Press the Clock Call button Setting the Clock ManuallyDisplaying the Time in Standby Mode Displaying the Date & TimeSelecting Sound Sources Using the CR-505DABAdjusting the Volume Using HeadphonesPlaying CDs Playing CDsSelecting Tracks by Number MP3 Disc Displaying InformationVarious Playback Random PlaybackRepeat Playback To Stop Memory Playback To Cancel Memory PlaybackMemory Playback To start memory playback, press the Play buttonPress the Menu button Using DABUsing DAB Ensemble Search ModeTurn the / control to select the com- ponent you require Component Search ModeSorted List Search Mode Sorting ComponentsPresetting Components Preset Search ModeDeleting Presets Displaying DAB Information Copying Preset ChannelsTuning into weak FM stations Using the RadioTuning the Radio Use the Tuning / buttons for fine tuningPress the Enter button to store the sta- tion Presetting FM Stations AutomaticallyPresetting Stations Manually Selecting PresetsRDS Radio Data System Other Functions Adjusting the Bass & TrebleUsing Direct Mode Press the remote controller’s Muting buttonTimer Examples TimersAbout the Timers Setting the TimersUse the / button to set the on time, and then press Enter Sleep indicator Turning Timers OffChecking Timer Settings Using the Sleep TimerAudio CD Disc NotesThis manual, MP3 files are referred to as tracks Disc LogoDisc Notes Handling DiscsTroubleshooting Mittent, and the ST FM Stereo indicator flickers?Radio presets no longer Reception is noisy, interAbnormal Behavior Restoring the Default SettingsSpecifications Onkyo Europe Electronics GmbHOnkyo Europe UK Office