Sanyo DC-DAB03 instruction manual Before Operation, CD Play, What to do if

BEFORE OPERATION

Turning the power on and off

Press the z/ON button, the display lights.

To turn the power off, press the z/ON button again, the display turns off, the clock display remains lit dimly. When economy display mode is needed,

press the /CLOCK/TIMER button, then the clock display goes out.

-When the mains lead is connected to the AC outlet, the unit will respond to commands from the remote control.

Direct start function

If the following buttons are pressed when the unit is in standby, the unit turns on automatically and the selected function is set.

CD section	i
DAB section	DAB
Remote control	CD i, DAB

Selecting the function

Press the FUNCTION button to select the desired function. Each time the button is pressed, the display changes to select following functions:

CD v Tuner v DAB v LINE v CD v …

The function is automatically selected when CD play is started or when the DAB button has been pressed.

-When the function selection is changed, CD play is automatically stopped.

Adjusting the volume

Turn the VOLUME control, or press the VOL – or VOL + button on the remote control. The volume level appears by numbers (VOL MIN ~ VOL MAX) on the display.

Bass expander system (Remote control only)

Press the BASS button to enhance the bass sound. “BASS ON” appears on the display briefly.

Selecting the sound mode (Remote control only)

Press the SOUND button to select the sound mode matching the music to be listened to.

POP: Pops, etc.

CLASSIC: Classical music, etc.

ROCK: Rock music, etc.

JAZZ: Jazz, etc.

WHAT TO DO IF ...

If the operation of the unit or display is not normal,

1.Disconnect the mains lead.

2.Connect the mains lead again.

3.Within 5 seconds while pressing the SET UP/RDS MODE button, press the MEMORY button at the same time.

4.Resume the operation.

CD PLAY

Use compact discs bearing the symbol shown. In addition to conventional 12 cm CDs, this system can be used to play 8 cm CDs without an adapter.

-This unit can play back the CD-R/RW that have

recorded music data as well. However, some CD-R/RWs can not be played back depending on the recording conditions.

-The CD-R/RW can’t be recorded in this unit.

If the disc is loaded, you can turn the unit on and begin play immediately by pressing the CD i button.

1.Press the FUNCTION button to select “CD” function. “READING” appears on the display, then “READING” is replaced by the CD mode display.

2.Press the OPEN/CLOSE button, disc tray slides out, “OPEN” appears.

3.Place the disc with the label facing up on the disc tray. (Place only one

disc at a time.)

4. Press the OPEN/CLOSE button again to close the disc tray. “CLOSE” appears briefly, then the total number of tracks and total playing time on the disc appear.

Note:

If no disc is loaded. “NO DISC” appears. If the disc is loaded with the label facing downward, or if the disc being loaded can’t be read by the unit, “UNDISC” appears. If this occurs, load the disc correctly or replace the damaged disc.

5. Press the CD i button. Play starts from the first track.

The current track number and elapsed playing time are displayed.

6.Press the n button to end disc play.

When the last track has been played, the player stops automatically.

Notes on handling compact discs

-Do not expose the disc to direct sunlight, high humidity or high temperatures for extended periods of time.

-Discs should be returned to their cases after use.

-Do not apply paper or write anything on the disc surface.

-Handle the disc by its edge. Do not touch the playing surface (glossy side).

-Fingerprints and dust should be carefully wiped off the playing surface of the disc with a soft cloth.

Wipe in a straight motion from the centre to the outside of the disc.

-Never use chemicals such as record cleaning sprays, antistatic sprays or fluids, benzene or thinner to clean compact discs.

To start play from the desired track

Select the track by using the e or f button, then press the CD i button.

Temporarily stopping play

Press the CD i button. Elapsed playing time blinks and “a” appears. To resume play, press the button again.

Skip play

To skip to track 6 while track 3 is playing, press the e button repeatedly until “6” appears (in the track section) on the display. To skip back to track 3 while track 6 is playing, press the f button repeatedly until “3” appears.

-The number buttons on the remote control can also be used for skip play. To skip to track 6 while one track is playing, press 6.

Search (forward/reverse)

If the e or f button is pressed during play, the player will search at high speed in the forward or reverse direction while the button is being pressed. When the button is released, normal play will continue.

-5-