Jensen SD1413 owner manual Loudness Band, Audio Mute Mute, Equalizer Selector PEQ, Beep Tone

Page 5

SD1413

SERIES

Select

Press the AUDIO

 

VOL

CONTROL button (4)

 

VOL

to step through the

 

 

menu of audio

FAD

BAS

functions: volume

 

 

(VOL), bass (BAS),

BAL

TRB

treble (TRB), balance

 

 

(BAL), fader (FAD),

and volume (VOL). When adjusting audio functions, the unit will automatically exit select mode and return to the normal display after five seconds or when another function is activated.

Bass

Press the AUDIO CONTROL button (4) twice until “BAS” appears in the display. Within five seconds, turn the AUDIO CONTROL (3) clockwise or counter clockwise to adjust the bass from “-10” to “+10”. “00” represents a flat response. The bass level is shown on the display for five seconds or until another function is activated.

Treble

Press the AUDIO CONTROL button (4) three times until “TRB” appears in the display. Within five seconds, turn the AUDIO CONTROL (3) clockwise or counter clockwise to adjust Treble from “-10” to “+10”. “00” represents a flat response. The treble level is shown on the display for five seconds or until another function is activated.

Balance

Press the AUDIO CONTROL button (4) four times until “BAL” appears in the display. Within five seconds, turn the AUDIO CONTROL (3) clockwise (or counter clockwise) to adjust Balance between the right and left speakers from “BAL 10R” (full right) to “BAL 10L” (full left). “BAL L=R” represents an equal balance level between the right and left speakers. The balance position is shown on the display for five seconds or until another function is activated.

Fader

Press the AUDIO CONTROL (4) five times until “FAD” appears in the display. Within five seconds, turn the AUDIO CONTROL (3) clockwise or counter clockwise to adjust balance between the front and rear speakers from “FAD 10R” (full rear) to “FAD 10F” (full front). “FAD F=R” represents an equal balance level between the front and rear speakers. The fader position is shown on the display for five seconds or until another function is activated.

Loudness (BAND)

Press and hold the LOUD/BAND button (5) for two seconds to activate the LOUD feature. When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. When activated, “LOUD”

appears on the display. Press LOUD/BAND again for two seconds to deactivate this feature.

Audio Mute (MUTE)

Press the MUTE button (6) to mute the audio volume. “MUTE” flashes on the display. Restore volume to the previous setting by pressing the mute button again, adjusting the AUDIO CONTROL.

Equalizer Selector (PEQ)

The equalizer function applies preset sound effects to the unit’s audio output signal. Press the PEQ button on the remote control to activate one of the following operating modes: FLAT, CLASSICS, POP M, ROCK M or DSP OFF. When the equalizer function is activated, the most recently selected bass/treble levels are ignored. If the bass and/or treble levels are adjusted while the equalizer function is active, the equalizer function will revert to FLAT. When the equalizer function is not active, the unit will return to the most recently selected bass and treble levels.

Beep Tone

The beep tone feature allows the selection of an audible beep tone to be heard each time a button is pressed on the face of the radio. To access the Beep Tone menu, press and hold the AUDIO CONTROL (4). Turn the AUDIO

3

Image 5
Contents SD1413 SD1413 Introduction ContentsToll-Free Installation Assistance Volume PowerOperating Instructions SourceLoudness Band SelectAudio Mute Mute Equalizer Selector PEQLiquid Crystal Display LCD Reset ButtonDisplay Disp Auxiliary InputAutomatic Tuning TuningManual Tuning Tuner OperationPreset Scan/Automatically Store PS/AS Preset StationsPreset Scan Automatically StorePI Program identification PS Program Service NameAF Alternative Frequencies List TP Traffic ProgramInsert CD CD Player OperationTrack Select Play/PauseDisc Repeat RPT CD Player Error CodesDisc Shuffle RDM Disc EjectMP3/WMA File Requirements MP3/WMA Encoder and CD Writer SettingsAcceptable Media Acceptable Disc FormatsEntering File and Folder Names Entering ID3 TagWriting Files into a Disc Electronic Shock ProtectionMP3/WMA Operation Search Characters Direct File Number SearchDirectory/File Search Root Directory SearchDisplay Information Loading a USB Device Using a USB Device or SD CardLoading an SD Card Navigating FilesRemote Control CD Player Care and MaintenanceCompact Discs CD Care and HandlingProblem Cause Corrective Action TroubleshootingSpecifications What is not covered? What is covered?Obtaining Warranty Service Who is covered?N1049