Jensen BT1613 owner manual Speaker Requirements, Preparation, ISO-DIN Installation

Step 3

Removal Key

Step 4b

Step 1

Speaker Requirements

Only connect speakers rated with a load impedance of 4 ohms. Speakers with a load impedance of less than 4 ohms could damage the unit.

Preparation

This unit is designed for installation in cars, trucks and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot locate one, call our customer support line at 1-800-323- 4815. (U.S.A. and Canada only.)

1To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.

NOTE: If this unit is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit.

2 Remove transport screws.

ISO-DIN Installation

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local car stereo shop for assistance on this type of installation.

1Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets

as they will be used to mount the new radio.

2 Carefully unsnap the plastic frame from the front of the new radio chassis. Remove and discard the frame.

3Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.

CAUTION: Do not exceed M5 X 9MM screw size. Longer screws may damage components inside the chassis.

4 Wire the new radio to the vehicle as outlined in the Mounting Sleeve Installation instructions.

5Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1.

CAUTION! Be careful not to damage the car wiring.

Mounting Sleeve Installation

1Push the REL button and remove the detachable front panel from the chassis.

2	Remove the trim ring by lifting in the center and pulling it off
	from either side.	1
3	Remove the mounting sleeve.
	a. Insert the removal keys straight back until they lock. If
	removal keys are inserted at an angle, they will not lock
	properly to release the unit.	2

b.Slide the mounting sleeve off the chassis.

4 Install the mounting sleeve in the dashboard.

a.Check the dashboard opening size by sliding the mounting

sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow.

b.Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs

outward as necessary to firmly secure the sleeve to the dashboard.

5Place the radio in front of the dashboard opening so the

	wiring can be brought through the mounting sleeve.
6	Follow the wiring diagram carefully and make certain all	TAB
	connections are secure and insulated with crimp connectors or
	electrical tape to ensure proper operation.
	WARNING! Only connect the unit to a 12-volt power supply with	DASHBOARD
	proper grounding.

7	After completing the wiring connections, attach the front panel
	and turn the unit on to confirm operation (vehicle ignition switch	Steps 8-9
	must be on). If the unit does not operate, recheck all wiring until
	the problem is corrected. Once proper operation is achieved,
	turn the ignition switch off and proceed with final mounting of the
	chassis.
8	Carefully slide the radio into the half-sleeve, making sure it is
	right-side-up until it is fully seated and the spring clips lock it into
	place.
9	Attach one end of the perforated support strap (supplied) to
	the screw stud on the rear of the chassis using the hex nut
	provided. Fasten the other end of the perforated strap to a
	secure part of the dashboard, either above or below the radio,
	using the screw and hex nut provided. Bend the strap, as necessary, to position it.
	CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from
	the weight of the radio or improper operation due to vibration.

10Re-attach the decorative trim ring.

11Re-attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit.

NOTE: For proper operation of the CD/MP3 player, the chassis must be mounted within 20° of horizontal. Make sure the unit is mounted within this limitation.