S T E P 2 0
If an amplifier is to be mounted onto the Stealthbox®.
Drill the mounting holes in the proper location. Apply silicone to the four supplied Phillip head screws before securing the amplifier.
Run speaker wire from the amplifier location to the speaker terminals. Attach the speaker wire to the terminals.
Double check the woofers for proper operation.
S T E P 2 1
1500 Series Trucks
Thread in the pair of socket cup set screws into the back of the Stealthbox®, leaving
HD Series Trucks
Back out the pair of socket cup set screws, leaving
|
| ||
I N C L U D E D H A R D W A R E |
|
| |
(4) #10 x 3/4 Phillip pan head sheet metal screws | (2) 3/8" - 16 x | ||
(2) | 3/8" Split Lock Washer | (2) 3" x 3" Wax Squares | |
(2) | 3/8" Flat Washer |
|
|
(2)3/8" x
P o w e r R e c o m m e n d a t i o n
Enclosure Type: Acoustic Suspension (sealed)
Driver Type:
Nominal Impedance: 2 ohms mono
Continuous Power Handling: 300 Watts
P o w e r R e c o m m e n d a t i o n
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
+12VDC | Ground Remote | Preamp Output Section | Bass Control | Amp LP Filter | Amplifier Input Section | |||
|
| Output Mode | Infrasonic Filter | Mode/Slope | Input V oltage | Input Sens. Signal Sensing | ||
|
|
| Off/30Hz | Off/12dB/24dB | Low/High | Off/On | ||
|
|
|
|
| +7 |
|
|
|
|
|
|
| +3 | +10 |
|
|
|
JL AUDIO 250/1 |
|
| +1 | +13 |
|
|
| |
|
|
|
|
|
|
| ||
monoblock subwoofer amplifier |
|
|
|
|
|
|
| |
|
| Left Ch. | Right Ch. | LF Boost (dB) | Filter Freq. (Hz) | Left Ch. | Right Ch. | |
STEALTHBOX WALL/ |
VEHICLE SHEET METAL |
LOCK WASHER+ |
HEX NUT |
SOCKET CUP SET SCREW |
FLAT WASHER+ |
THREADED INSERT7 |
FENDER WASHER+ |
S T E P 2 2
From inside the truck, position the Stealthbox® into the mounting location. From the outside of the truck(between the cab wall and the bed wall) place the supplied fender washer, flat washer, lock washer and then nut onto each exposed socket cup set screw. Use a long 3/8" open end wrench or ratcheting box end to secure the mounting hardware. If you have big hands and arms, time to get that smaller friend of yours to help out.
Note: For added protection it is recommended that you apply a bead of silicone between the vehicle and the fender washer. After the bolt assembly is tightly secured, it is also recommended that vehicle under- coating material is applied to the exposed assembly.
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please go back in the instructions in reverse to mount all factory paneling back to it's original form.
Please refer to the Power Recommendation section for an amplifier recommendation and basic
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.
M I D / H I G H F r e q u e n c y D r i v e r F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
Fits JL Audio Models:
Rear Speaker Size / Location:
Fits JL Audio Models:
(954) | www.jlaudio.com |
|
|
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
Page 3 • JL Audio, Inc 2006
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A