Advanced Functions, Punch-Through Programming

ADVANCED FUNCTIONS

The RCP 6 remote control not only operates the AVR 247 and DVD 38, but it also serves as a universal remote that may be programmed to operate many of your other home theater components. The punch- through and macro features add even more flexibility and versatility.

Punch-Through Programming

The RCP 6 remote allows you to select one component for the remote to operate, while simultaneously setting certain groups of controls to operate another component. For example, while using the remote to control video functions on your TV, you may wish to use your cable box to change channels and the AVR to control the volume.

This is possible using punch-through programming.

NOTE: It is not necessary to program the remote to control your DVD player’s transport controls while the AVR or a device connected to the VID2 or VID3 inputs is in use, as the remote is preprogrammed at the factory with this function.

To program punch-through control while operating any device:

1.Press and hold the Input Selector (or AVR Selector) for the main device the remote will be operating until the Input Selector lights, the Program Indicator LED flashes and the remote enters Program mode.

2.Select the type of punch-through programming:

a)To program volume control punch-through, press the Volume Up Button.

b)To program channel control punch-through, press the Volume Down Button.

NOTE: Do not program channel-control punch-through for the AVR. Doing so will override the Sleep command, which is not accessible in any other way, and the DSP Surround Mode Selector. If you have inadvertently done so, repeat Steps 1 through 3, but press the AVR Selector in both Steps 1 and 3.

c)To program transport control punch-through, press the Play Button.

3.Press the Input Selector (or AVR Selector) for the device whose volume, channel or transport controls you would like to be active while operating the device you selected in the first step. The LED will flash green to confirm the programming.

For example, if you wish to watch your TV (programmed into the Video 3 Button) while changing channels using your cable box (Video 2), first press the Video 3 Button until the LED flashes. Then press the Volume Down Button, followed by the Video 2 Button.

To undo punch-through programming, follow the same steps as above, but press the same Input (or AVR) Selector in Steps 1 and 3.

NOTE: The AVR, VID2 and VID3 devices are factory-programmed with transport-control punch-through to operate the DVD player. You may reprogram these selectors following the instructions in Steps 1 through 3 to operate another device, such as a CD player.

If you wish to reprogram these selectors to have no transport- control punch-through, follow the same procedure as for programming punch-through, but in Step 3 press either of the other two of these three selectors. For example, to remove transport-control punch-through from the VID2 device, follow the instructions in Steps 1 through 3, but press either the AVR or VID3 Button in Step 3.

Macros

Macros are used to program sequences of up to 19 commands that are executed with a single button press. Macros are well-suited for Power On and Off commands, to send out a favorite multidigit channel number with one button press, or to have the ability to send out a code sequence to control another device while the remote is operating one device but with more flexibility than the built-in punch- through controls.

Some commands may not be programmed into macros: Mute, Dim, Channel Up/Down and any of the Surround Mode commands.

NOTE: Use caution when programming complicated macros. It isn’t possible to program a pause or delay before sending commands after powering on, and the component may not be ready to respond to commands instantaneously after powering on.

To program, or “record,” a macro, follow these steps:

1.Simultaneously press one of the four Macro Buttons or the Power On Button and the Mute Button at the same time to enter Program mode.

2.Press the Input (or AVR) Selector for each device before you enter commands to be transmitted to that device. This step counts as one of the 19 commands allowed for each macro.

NOTE: Even if you previously switched one of the dual-source Input Selectors (DVD/CD, TAPE/THE BRIDGE, HDMI 1/HDMI 2) to the primary or secondary source prior to programming the macro, the remote always requires you to press any of these selectors once to program the macro to select the primary source and twice for the secondary source.

3.For the Power On command, do not press the Power On Button. Press the Mute Button instead.

4.Press the Power Off Button to program the Power Off command.

5.Press the Sleep Button to end the programming process.

It isn’t possible to “edit” a command within a macro. However, you may erase the macro as follows:

1.Simultaneously press and hold the Mute Button and the Macro Button containing the macro until the Program LED flashes.

2.Press the Surround Button to erase the macro.

Resetting the Remote

To reset the remote to its factory defaults, simultaneously press and hold any Input Selector and the “0” Numeric Key. When the LED flashes amber, enter the code “333”. When the green LED goes out, the remote will have been fully reset.