Hifionics HFI100.4, HFI1000D, HFI1500D Channels 3/4 HI Pass 100 Hz, Stereo Interconnect RCA Cable

Page 7

HFi55.4 / HFi100.4 4-CHANNEL AMPLIFIER APPLICATIONS

Front/Rear high pass, using a 2 channel amplifier for mono sub bass

The combination of a 2 and a 4 channel amplifier, utilizing their built in crossovers, makes it a snap to put together a full system with front and rear highs, with mono sub bass.

Interconnect cable checklist:

-Using good quality RCA cables, feed the front and rear outputs of a head unit to the inputs of the 4 channel amplifier as shown.

-Also connect the LINE OUT of the 4 channel amplifier to the LINE INPUT of the 2 channel amplifier as shown.

Mono bass woofer wiring:

Connect the mono speaker positive terminal to the LEFT +, and its negative terminal to RIGHT -.

Switch setting checklist:

4 channel highs amplifier:

-1/2CH X-OVER: HPF

-3/4CH X-OVER: HPF

2 channel bass amplifier: - X-OVER switch: LPF

Crossover frequency control checklist: - 4 channel highs amplifier:

Channels 1/2:

-HI PASS: 100 Hz

LOW PASS: N/A

Channels 3/4:

-HI PASS: 100 Hz

-LOW PASS: N/A

2 channel bass amplifier:

-HI PASS (Subsonic filter): 10 Hz to 40 Hz

-LOW PASS: 80 Hz

Please note that these frequency points are suggestions only. Refer to the loudspeaker manufacturer specifications and the section “Setting up systems after installation for best performance”

Level control checklist:

-Refer to the section “Setting up systems after installation for best performance”

Minimum final loudspeaker impedances:

-2 ohm per channel in stereo mode.

-4 ohm mono bridged.

 

 

 

 

CH3/4

 

 

 

 

CH1/2

6V 0.2V

LEVEL

6V 0.2V

 

LEVEL

0dB 12dB

BASS EQ

0dB 12dB

 

BASS EQ

FULL LPF HPF

X-OVER

FULL LPF HPF

 

X-OVER

60Hz 12KHz

HPF

60Hz 12KHz

 

HPF

30Hz 250Hz

LPF

30Hz 250Hz

 

LPF

2 3 4

MODE

 

PROTECT

POWER

 

 

 

 

LINE OUT

HF

 

 

 

 

- RIGHT + - LEFT +

 

 

 

 

 

 

 

 

 

 

 

 

 

OUTPUT CH 3/4

 

BRIDGED

 

 

 

 

 

 

 

 

 

 

 

 

 

CH 1/2 SPEAKER

 

 

 

RIGHT + - LEFT +

 

 

 

 

 

 

 

 

 

 

BRIDGED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FUSE

 

 

 

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND REM BATT+12V

 

 

POWER INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEREO

INTERCONNECT

RCA CABLE

R

L

OUTPUT

R

L

INPUT

 

6V 0.2V

LEVEL

 

0dB 12dB

BASS EQ

 

FULL LPF HPF

X-OVER

 

60Hz 12KHz

HPF

 

30Hz 250Hz

LPF

 

MONO STEREO

MODE

 

PROTECT

POWER

HF

 

 

SUBWOOFER

SPEAKER OUTPUT

 

+

BRIDGED

RIGHT + - LEFT

 

 

-

FUSE

REMGNDBATT+12V

 

INPUTPOWER

CHASSIS GROUND

 

 

TO BATTERY +12v

 

 

VIA FUSE

 

 

REMOTE TURN-ON

5

Image 7
Contents Page HFi High Performance Amplifiers Wood General Installation ProcedureHFi100.2 2-CHANNEL Amplifiers Amplifier Feature DescriptionsSwitch setting checklist Crossover frequency control checklist Channels 1/2 Level control checklistChannel full range units Stereo Interconnect RCA Cable Channels 3/4 HI Pass 100 HzSubwoofer MonoPage Setting UP Systems After Installation for Best Performance Electrical interference Troubleshooting a SystemMaxxsonics Limited Warranty OEM Integration Accessories MAXX-LINK PART# A1109